Poulan 197053 manual Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1) 1/2" wrench

Utility knife

(1) 3/4" wrench

Tire pressure gauge

Pliers

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

Remove all accessible loose parts and parts cartons from carton.

Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels fl at.

Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

Slide extension shaft onto lower steering shaft.

Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

Position front wheels of the tractor so they are pointing straight forward.

Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

Assemble large fl at washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

Snap steering wheel insert into center of steering wheel.

Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

5/16 HEX BOLT

5/16 LOCK WASHER

LARGE FLAT

WASHER

STEERING

WHEELSTEERING BOOT

TABS

ADAPTER

EXTENSION

SHAFT

LOWER

STEERING

SHAFT

TAB

SLOTS

FIG. 1

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment bolt.

Remove adjustment bolt, lock washer and fl at washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

Pivot seat and pan forward and assemble adjust- ment bolt, lockwasher and fl at washer loosely. Do not tighten

Lower seat into operating position and sit on seat.

Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

Get off seat without moving its adjusted position.

Raise seat and tighten adjustment bolt securely.

6

Image 6
Contents PD15538LT Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Reverse Operation System ROSTo Operate Mower See Fig To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips General Recommendations MaintenanceLubrication Chart Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Belts BatteryEngine Transaxle CoolingAIR Filter CleaningClean AIR Screen MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Brake To Check BrakeTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

197053 specifications

The Poulan 197053 is a standout model in the realm of outdoor power equipment, designed specifically for those who demand efficiency, reliability, and effectiveness for their lawn care and landscaping tasks. This model showcases an array of features and technologies that make it an ideal choice for both residential and professional use.

At the heart of the Poulan 197053 is its powerful engine. The machine is equipped with a robust 46cc two-stroke engine that delivers potent cutting power. This engine provides the necessary torque to tackle a variety of tasks, from trimming grass and hedges to more demanding clearing projects. The advanced engine technology not only ensures reliable performance but also promotes fuel efficiency, allowing users to complete jobs without frequent refueling.

One of the key characteristics of the Poulan 197053 is its user-friendly design. Weighing in at a manageable size, this model is built for ease of use. It features an ergonomic handle that provides comfort during prolonged periods of operation, reducing fatigue and enhancing the overall user experience. The lightweight construction ensures that the machine can easily be maneuvered, making it ideal for both small and large outdoor spaces.

In terms of cutting performance, the Poulan 197053 boasts a durable cutting blade that is designed for precision and longevity. The sharp blade ensures a clean cut, promoting the health of your plants and grass. Furthermore, the model offers adjustable height settings, allowing users to customize their cutting experience according to the specific requirements of their lawn or garden.

Technology plays a crucial role in the performance of the Poulan 197053. The model incorporates features such as an automatic oiling system, which ensures that the cutting blade remains adequately lubricated, thereby extending its lifespan and minimizing maintenance needs. The quick-release air filter also promotes easy access for cleaning and replacement, ensuring optimal engine performance over time.

Durability is another hallmark of the Poulan 197053. Constructed with high-quality materials, it is designed to withstand the rigors of outdoor use. The rugged build not only provides longevity but also enhances the effectiveness of the machine in diverse working conditions.

In conclusion, the Poulan 197053 is an exceptional choice for anyone seeking a reliable, feature-rich outdoor power tool. With its powerful engine, ergonomic design, advanced technology, and robust construction, it stands out as a top contender in the garden equipment market. Whether you are a homeowner maintaining your yard or a professional landscaper, this model offers the performance you need to achieve stunning results.