Poulan 197053 manual Before Starting the Engine, Check Engine OIL Level, ADD Gasoline

Page 13

OPERATION

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already fi lled with summer weight oil.

Check engine oil with tractor on level ground.

Remove oil fi ll cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfi ll.

For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Maintenance section of this manual).

To change engine oil, see the Maintenance section in this manual.

ADD GASOLINE

Fill fuel tank to bottom of fi ller neck. Do not overfi ll. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can at- tract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 5)

When starting the engine for the fi rst time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

Place gear shift lever in neutral (N) position.

Move attachment clutch to “DISENGAGED” position.

Move throttle control to choke () position.

NOTE: Before starting, read the warm and cold starting procedures below.

Insert key into ignition and turn key clockwise to“START” position and release key as soon as engine starts. Do not run starter continuously for more than fi fteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke ( ) position and retry.

WARM WEATHER STARTING (50° F and above)

When engine starts, move the throttle control to the fast position.

The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING ( 50° F and below)

When engine starts, allow engine to run with the throttle control in the choke () position until the engine runs roughly, then move throttle control to fast position.This may require an engine warm-up period from several seconds to several minutes, depending on the tem- perature.

The attachments can also be used during the engine warm-up period.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

13

Image 13
Contents Always Wear EYE Protection During Operation PD15538LTSafe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Contents of Hardware Pack Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Reverse Operation System ROSTo Operate on Hills To TransportCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMowing Tips Lubrication Chart MaintenanceGeneral Recommendations Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine BatteryBelts Transaxle CoolingClean AIR Screen CleaningAIR Filter MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig To Check BrakeTo Adjust Steering Wheel ALIGN- Ment Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

197053 specifications

The Poulan 197053 is a standout model in the realm of outdoor power equipment, designed specifically for those who demand efficiency, reliability, and effectiveness for their lawn care and landscaping tasks. This model showcases an array of features and technologies that make it an ideal choice for both residential and professional use.

At the heart of the Poulan 197053 is its powerful engine. The machine is equipped with a robust 46cc two-stroke engine that delivers potent cutting power. This engine provides the necessary torque to tackle a variety of tasks, from trimming grass and hedges to more demanding clearing projects. The advanced engine technology not only ensures reliable performance but also promotes fuel efficiency, allowing users to complete jobs without frequent refueling.

One of the key characteristics of the Poulan 197053 is its user-friendly design. Weighing in at a manageable size, this model is built for ease of use. It features an ergonomic handle that provides comfort during prolonged periods of operation, reducing fatigue and enhancing the overall user experience. The lightweight construction ensures that the machine can easily be maneuvered, making it ideal for both small and large outdoor spaces.

In terms of cutting performance, the Poulan 197053 boasts a durable cutting blade that is designed for precision and longevity. The sharp blade ensures a clean cut, promoting the health of your plants and grass. Furthermore, the model offers adjustable height settings, allowing users to customize their cutting experience according to the specific requirements of their lawn or garden.

Technology plays a crucial role in the performance of the Poulan 197053. The model incorporates features such as an automatic oiling system, which ensures that the cutting blade remains adequately lubricated, thereby extending its lifespan and minimizing maintenance needs. The quick-release air filter also promotes easy access for cleaning and replacement, ensuring optimal engine performance over time.

Durability is another hallmark of the Poulan 197053. Constructed with high-quality materials, it is designed to withstand the rigors of outdoor use. The rugged build not only provides longevity but also enhances the effectiveness of the machine in diverse working conditions.

In conclusion, the Poulan 197053 is an exceptional choice for anyone seeking a reliable, feature-rich outdoor power tool. With its powerful engine, ergonomic design, advanced technology, and robust construction, it stands out as a top contender in the garden equipment market. Whether you are a homeowner maintaining your yard or a professional landscaper, this model offers the performance you need to achieve stunning results.