Poulan 196712 manual HOW to USE Your Tractor

Page 12

OPERATION

The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while op- erating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.

HOW TO USE YOUR TRACTOR

TO SET PARKING BRAKE (See Fig. 7)

Your tractor is equipped with an operator presence sens- ing switch. When engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine.

Depress clutch/brake pedal into full “BRAKE” position and hold.

Place parking brake lever in “ENGAGED” position and release pressure from clutch/brake pedal. Pedal should remain in “BRAKE” position. Make sure parking brake will hold tractor secure.

IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY POSITION OTHER THAN "STOP" WILL CAUSE THE BATTERY TO BE DISCHARGED, (DEAD).

NOTE: Under certain conditions when tractor is standing idle with the engine running, hot engine exhaust gases may cause “browning” of grass. To eliminate this possibility, al- ways stop engine when stopping tractor on grass areas.

CAUTION: Always stop tractor com- pletely,as described above,before leav- ing the operator's position; to empty grass catcher, etc.

ATTACHMENT CLUTCH SWITCH

PULL OUT TO"ENGAGE"

CHOKE

CONTROLPUSH IN TO "DISENGAGE"

THROTTLE

CONTROL

"BRAKE"

 

POSITION

IGNITION

 

 

KEY

 

MOTION CONTROL

 

LEVER

CLUTCH/BRAKE

PARKING BRAKE

PEDAL "DRIVE"

"ENGAGED"

POSITION HEIGHT

POSITION

ADJUSTMENT

PARKING BRAKE

KNOB

"DISENGAGED" POSITION

 

FIG. 7

STOPPING (See Fig. 7)

MOWER BLADES -

To stop mower blades,move attachment clutch switch to “DISENGAGED” position.

GROUND DRIVE -

To stop ground drive, depress clutch/brake pedal into full “BRAKE” position..

Move motion control lever to neutral (N) position.

IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/ BRAKE PEDAL IS DEPRESSED.

ENGINE -

Move throttle control between half and full speed (fast) position.

NOTE: Failure to move throttle control between half and full speed (fast) position, before stopping may cause engine to “backfire”.

Turn ignition key to “STOP” position and remove key. Always remove key when leaving tractor to prevent unauthorized use.

Never use choke to stop engine.

TO USE THROTTLE CONTROL (See Fig. 7)

Always operate engine at full throttle.

Operating engine at less than full throttle reduces the battery charging rate.

Full throttle offers the best bagging and mower perfor- mance.

TO USE CHOKE CONTROL (See Fig. 7)

Use choke control whenever you are starting a cold engine. Do not use to start a warm engine.

To engage choke control, pull knob out. Slowly push knob in to disengage.

TO MOVE FORWARD AND BACKWARD (See Fig. 7)

The direction and speed of movement is controlled by the motion control lever.

Start tractor with motion control lever in neutral (N) position.

Release parking brake.

Slowly move motion control lever to desired position.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 7)

The cutting height is controlled by turning the height ad- justment knob in desired direction.

Turn knob clockwise (

) to raise cutting height.

Turn knob counterclockwise (

) to lower cutting

 

height.

 

 

The cutting height range is approximately 1-1/2" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

12

Image 12
Contents XT24H48YT Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Unassembled Parts Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigReverse Operation System ROS To Operate on HillsBefore Starting the Engine To Transport See FigsCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Check Operator Presence SystemEngine Cleaning Service and Adjustments To Install MowerTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsMower Drive Belt Installation To Replace Mower Drive BeltTo Check and Adjust Brake See Fig To Replace Mower Blade Secondary Drive Belt See FigTransaxle Motion Control Lever Neutral Adjustment See Fig Belt InstallationTo Replace Motion Drive Belt See Fig Belt RemovalTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Attach Jumper CablesTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points Engine dies when Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

196712 specifications

The Poulan 196712 is a versatile and powerful chainsaw designed to meet the demands of both professional landscapers and avid homeowners alike. Renowned for its durability and reliability, the Poulan 196712 is equipped with numerous features that enhance its performance and ease of use.

At the heart of the Poulan 196712 is a robust 46 cc, 2-cycle engine that delivers ample power while maintaining fuel efficiency. This engine is designed to handle a variety of cutting tasks, from felling small trees to trimming branches and clearing brush. The chainsaw operates at a high RPM, enabling it to cut through tough materials quickly and effortlessly.

One of the standout features of the Poulan 196712 is its anti-vibration technology. This system is designed to reduce the amount of vibration experienced by the user during operation, providing greater comfort and control. With less vibration, users can work for extended periods without fatigue, enhancing productivity and reducing the risk of injury.

The chainsaw features a well-designed air filtration system that helps keep the engine running smoothly. The easily accessible air filter can be cleaned or replaced without the need for special tools, ensuring optimal engine performance and prolonging the life of the chainsaw.

Safety is a top priority with the Poulan 196712. The chainsaw is equipped with a chain brake that engages automatically in the event of kickback, protecting the user from potential harm. Additionally, the front hand guard adds an extra layer of safety, allowing users to work confidently in a variety of conditions.

Another significant feature of the Poulan 196712 is its tool-less chain tensioning system. This feature allows users to adjust the chain tension quickly and easily without the need for additional tools. Proper chain tensioning is critical for optimal performance and safety, making this feature particularly convenient for users who value efficiency.

Finally, the Poulan 196712 boasts a lightweight design, making it easy to maneuver during extended use. Its ergonomic handle provides a comfortable grip, further enhancing user control.

In summary, the Poulan 196712 is a powerful and feature-rich chainsaw that combines performance, safety, and ease of use. With its advanced technologies and thoughtful design, it is an excellent choice for anyone looking to tackle their cutting tasks effectively and efficiently. Whether for professional use or personal projects, the Poulan 196712 stands out as a reliable tool in the world of outdoor equipment.