Poulan 196712 manual Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel ALIGN- Ment

Page 25

SERVICE AND ADJUSTMENTS

MOTION CONTROL

NEUTRAL

LEVER

LOCK GATE

 

ADJUSTMENT

BOLT

FIG. 26

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See“PURGETRANSMISSION” in the Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor.If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 27)

TO START ENGINE WITH A WEAK BATTERY (See Fig. 28)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 27

FIG. 28

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Always Wear EYE Protection During Operation XT24H48YTSafe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationIII. Children ServiceIV. Towing Table of Contents Unassembled Parts Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidAssemble Gauge Wheels to Mower Deck See Fig Check Battery See FigInstall Mower and Drive Belt See Figs Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigReverse Operation System ROS To Operate on HillsTo Transport See Figs Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP Lubrication Chart MaintenanceGeneral Recommendations Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Check Operator Presence SystemEngine Cleaning To Install Mower Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Drive Belt Mower Drive Belt InstallationTo Replace Mower Blade Secondary Drive Belt See Fig To Check and Adjust Brake See FigBelt Installation Transaxle Motion Control Lever Neutral Adjustment See FigTo Replace Motion Drive Belt See Fig Belt RemovalTo Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN/CAMBER To Attach Jumper CablesTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace FuseOther StorageFuel System Engine OILTroubleshooting Points Engine dies when Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

196712 specifications

The Poulan 196712 is a versatile and powerful chainsaw designed to meet the demands of both professional landscapers and avid homeowners alike. Renowned for its durability and reliability, the Poulan 196712 is equipped with numerous features that enhance its performance and ease of use.

At the heart of the Poulan 196712 is a robust 46 cc, 2-cycle engine that delivers ample power while maintaining fuel efficiency. This engine is designed to handle a variety of cutting tasks, from felling small trees to trimming branches and clearing brush. The chainsaw operates at a high RPM, enabling it to cut through tough materials quickly and effortlessly.

One of the standout features of the Poulan 196712 is its anti-vibration technology. This system is designed to reduce the amount of vibration experienced by the user during operation, providing greater comfort and control. With less vibration, users can work for extended periods without fatigue, enhancing productivity and reducing the risk of injury.

The chainsaw features a well-designed air filtration system that helps keep the engine running smoothly. The easily accessible air filter can be cleaned or replaced without the need for special tools, ensuring optimal engine performance and prolonging the life of the chainsaw.

Safety is a top priority with the Poulan 196712. The chainsaw is equipped with a chain brake that engages automatically in the event of kickback, protecting the user from potential harm. Additionally, the front hand guard adds an extra layer of safety, allowing users to work confidently in a variety of conditions.

Another significant feature of the Poulan 196712 is its tool-less chain tensioning system. This feature allows users to adjust the chain tension quickly and easily without the need for additional tools. Proper chain tensioning is critical for optimal performance and safety, making this feature particularly convenient for users who value efficiency.

Finally, the Poulan 196712 boasts a lightweight design, making it easy to maneuver during extended use. Its ergonomic handle provides a comfortable grip, further enhancing user control.

In summary, the Poulan 196712 is a powerful and feature-rich chainsaw that combines performance, safety, and ease of use. With its advanced technologies and thoughtful design, it is an excellent choice for anyone looking to tackle their cutting tasks effectively and efficiently. Whether for professional use or personal projects, the Poulan 196712 stands out as a reliable tool in the world of outdoor equipment.
Top Page Image Contents