Poulan 196712 manual To Replace Fuse, To Adjust Throttle Control Cable, To Adjust Choke Control

Page 26

SERVICE AND ADJUSTMENTS

REPLACING BATTERY (See Fig. 29)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acci- dental grounding.

•Lift hood to raised position.

•Remove terminal guard.

•Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•Reinstall terminal guard.

•First connect RED battery cable to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely.

•Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely

•Close terminal access doors.

•Close hood.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 30)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

02141

TERMINAL ACCESS DOOR

KEPS NUT

HEX BOLT

POSITIVE (RED)

CABLE

FIG. 30

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.

TERMINAL GUARD

NEGATIVE (BLACK)

CABLE

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and ad- justment should not be necessary. If adjustment is neces-

FIG. 29

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

sary, see engne manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents XT24H48YT Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIV. Towing ServiceIII. Children Table of Contents Unassembled Parts To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsCheck Engine OIL Level Before Starting the EngineTo Transport See Figs ADD GasolineAutomatic Transmission Warm UP Mowing TipsPurge Transmission General Recommendations MaintenanceLubrication Chart Before Each USETo Sharpen Blade See Fig TractorBlade Removal See Fig Check Operator Presence SystemEngine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower To Level Mower Housing FRONT-TO-BACK Adjustment See FigsMower Drive Belt Installation To Replace Mower Drive BeltTo Check and Adjust Brake See Fig To Replace Mower Blade Secondary Drive Belt See FigTo Replace Motion Drive Belt See Fig Transaxle Motion Control Lever Neutral Adjustment See FigBelt Installation Belt RemovalFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment To Attach Jumper CablesTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points Engine dies when Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

196712 specifications

The Poulan 196712 is a versatile and powerful chainsaw designed to meet the demands of both professional landscapers and avid homeowners alike. Renowned for its durability and reliability, the Poulan 196712 is equipped with numerous features that enhance its performance and ease of use.

At the heart of the Poulan 196712 is a robust 46 cc, 2-cycle engine that delivers ample power while maintaining fuel efficiency. This engine is designed to handle a variety of cutting tasks, from felling small trees to trimming branches and clearing brush. The chainsaw operates at a high RPM, enabling it to cut through tough materials quickly and effortlessly.

One of the standout features of the Poulan 196712 is its anti-vibration technology. This system is designed to reduce the amount of vibration experienced by the user during operation, providing greater comfort and control. With less vibration, users can work for extended periods without fatigue, enhancing productivity and reducing the risk of injury.

The chainsaw features a well-designed air filtration system that helps keep the engine running smoothly. The easily accessible air filter can be cleaned or replaced without the need for special tools, ensuring optimal engine performance and prolonging the life of the chainsaw.

Safety is a top priority with the Poulan 196712. The chainsaw is equipped with a chain brake that engages automatically in the event of kickback, protecting the user from potential harm. Additionally, the front hand guard adds an extra layer of safety, allowing users to work confidently in a variety of conditions.

Another significant feature of the Poulan 196712 is its tool-less chain tensioning system. This feature allows users to adjust the chain tension quickly and easily without the need for additional tools. Proper chain tensioning is critical for optimal performance and safety, making this feature particularly convenient for users who value efficiency.

Finally, the Poulan 196712 boasts a lightweight design, making it easy to maneuver during extended use. Its ergonomic handle provides a comfortable grip, further enhancing user control.

In summary, the Poulan 196712 is a powerful and feature-rich chainsaw that combines performance, safety, and ease of use. With its advanced technologies and thoughtful design, it is an excellent choice for anyone looking to tackle their cutting tasks effectively and efficiently. Whether for professional use or personal projects, the Poulan 196712 stands out as a reliable tool in the world of outdoor equipment.
Top Page Image Contents