Poulan 196712 manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 27

STORAGE

Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more.

WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

•Clean entire tractor (See “CLEANING” in the Mainte- nance section of this manual).

•Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

•Lubricate as shown in the Maintenance section of this manual.

•Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

•Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BATTERY

•Fully charge the battery for storage.

•After a period of time in storage, battery may require recharging.

•To help prevent corrosion and power leakage during long periods of storage, battery cables should be dis- connected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Mainte- nance section of this manual).

•After cleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals.

•If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANTTO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTUREWHICH LEADSTO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

•Empty the fuel tank by starting the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in mini- mizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

•Remove spark plug(s).

•Pour one ounce of oil through spark plug hole(s) into cylinder(s).

•Turn ignition key to “START” position for a few seconds to distribute oil.

•Replace with new spark plug(s).

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your tractor indoors and cover it to give protection from dust and dirt.

•Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.

IMPORTANT: NEVER COVERTRACTOR WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Always Wear EYE Protection During Operation XT24H48YTII. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationService III. ChildrenIV. Towing Table of Contents Unassembled Parts Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See Fig Check Battery See FigInstall Mower and Drive Belt See Figs Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig Reverse Operation System ROSADD Gasoline Before Starting the EngineTo Transport See Figs Check Engine OIL LevelMowing Tips Purge TransmissionAutomatic Transmission Warm UP Before Each USE MaintenanceLubrication Chart General RecommendationsCheck Operator Presence System TractorBlade Removal See Fig To Sharpen Blade See FigEngine Cleaning Service and Adjustments To Install MowerTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Drive Belt Mower Drive Belt InstallationTo Replace Mower Blade Secondary Drive Belt See Fig To Check and Adjust Brake See FigBelt Removal Transaxle Motion Control Lever Neutral Adjustment See FigBelt Installation To Replace Motion Drive Belt See FigTo Attach Jumper Cables Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Replace Fuse To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Points Engine dies when Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

196712 specifications

The Poulan 196712 is a versatile and powerful chainsaw designed to meet the demands of both professional landscapers and avid homeowners alike. Renowned for its durability and reliability, the Poulan 196712 is equipped with numerous features that enhance its performance and ease of use.

At the heart of the Poulan 196712 is a robust 46 cc, 2-cycle engine that delivers ample power while maintaining fuel efficiency. This engine is designed to handle a variety of cutting tasks, from felling small trees to trimming branches and clearing brush. The chainsaw operates at a high RPM, enabling it to cut through tough materials quickly and effortlessly.

One of the standout features of the Poulan 196712 is its anti-vibration technology. This system is designed to reduce the amount of vibration experienced by the user during operation, providing greater comfort and control. With less vibration, users can work for extended periods without fatigue, enhancing productivity and reducing the risk of injury.

The chainsaw features a well-designed air filtration system that helps keep the engine running smoothly. The easily accessible air filter can be cleaned or replaced without the need for special tools, ensuring optimal engine performance and prolonging the life of the chainsaw.

Safety is a top priority with the Poulan 196712. The chainsaw is equipped with a chain brake that engages automatically in the event of kickback, protecting the user from potential harm. Additionally, the front hand guard adds an extra layer of safety, allowing users to work confidently in a variety of conditions.

Another significant feature of the Poulan 196712 is its tool-less chain tensioning system. This feature allows users to adjust the chain tension quickly and easily without the need for additional tools. Proper chain tensioning is critical for optimal performance and safety, making this feature particularly convenient for users who value efficiency.

Finally, the Poulan 196712 boasts a lightweight design, making it easy to maneuver during extended use. Its ergonomic handle provides a comfortable grip, further enhancing user control.

In summary, the Poulan 196712 is a powerful and feature-rich chainsaw that combines performance, safety, and ease of use. With its advanced technologies and thoughtful design, it is an excellent choice for anyone looking to tackle their cutting tasks effectively and efficiently. Whether for professional use or personal projects, the Poulan 196712 stands out as a reliable tool in the world of outdoor equipment.
Top Page Image Contents