Poulan 404402 Check Tire Pressure, Check Deck Levelness, Check for Proper Position of ALL Belts

Page 6

ASSEMBLY

•Release parking brake by depressing brake pedal.

•Place freewheel control in disengaged position to dis- engage transmission (See “TO TRANSPORT” in the Operation section of this manual).

•Roll tractor forward off skid.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

•Sit on seat in operating position, depress brake pedal and set the parking brake.

•Raise attachment lift lever to its highest position.

•Remove key from bag and start the engine (see "TO START" in the Operation section of this manual). After engine has started, move throttle control to idle (slow) position.

•Release parking brake.

•Slowly depress forward drive pedal and drive tractor off skid.

•Apply brake to stop tractor and set parking brake.

•Turn ignition key to "STOP" position.

Continue with the instructions that follow.

CHECK TIRE PRESSURE

The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance.

•Reduce tire pressure to PSI shown on tires.

CHECK DECK LEVELNESS

For best cutting results, mower housing should be properly leveled. See “TO LEVEL MOWER HOUSING”in the Service and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF ALL BELTS

See the figures that are shown for replacing motion and mower blade drive belts in the Service and Adjustments section of this manual. Verify that the belts are routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your tractor, check to see that the brake is operating properly. See “TO CHECK BRAKE” in the Service and Adjustments section of this manual.

✓CHECKLIST

BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH TO ASSURE THATYOU RECEIVE THE BEST PER- FORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT.

PLEASE REVIEW THE FOLLOWING CHECKLIST:

✓All assembly instructions have been completed.

✓No remaining loose parts in carton.

✓Battery is properly prepared and charged.

✓Seat is adjusted comfortably and tightened securely.

✓All tires are properly inflated. (For shipping purposes, the tires were overinflated at the factory).

✓Be sure mower deck is properly leveled side-to-side/ front-to-rear for best cutting results. (Tires must be properly inflated for leveling).

✓Check mower and drive belts. Be sure they are routed properly around pulleys and inside all belt keepers.

✓Check wiring. See that all connections are still secure and wires are properly clamped.

✓Before driving tractor, be sure freewheel control is in “transmission engaged” position (see “TO TRANS- PORT” in the Operation section of this manual).

WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY EXTRA ATTENTION TO THE FOLLOWING IMPORTANT ITEMS:

✓Engine oil is at proper level.

✓Fuel tank is filled with fresh, clean, regular unleaded gasoline.

✓Become familiar with all controls, their location and function. Operate them before you start the engine.

✓Be sure brake system is in safe operating condition.

✓Be sure Operator Presence System and Reverse Op- eration System (ROS) are working properly (See the Operation and Maintenance sections in this manual).

✓It is important to purge the transmission before oper- ating your tractor for the first time. Follow proper start- ing and transmission purging instructions (See “TO START ENGINE” and “PURGE TRANSMISSION” in the Operation section of this manual).

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PB24H48YT Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationService III. ChildrenIV. Towing Table of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS on PositionHOW to USE Your Tractor StoppingSystem Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Service REMINDER/HOUR MeterBefore Starting the Engine Check Engine OIL LevelTo Start Engine See Fig Purge TransmissionAutomatic Transmission Warm UP Mowing Tips Maintenance Before Each USEBrake Operation BatteryTractor TiresEngine Spark Plugs CleaningMuffler IN-LINE Fuel Filter See FigTractor See Fig Service and AdjustmentsTo Install Mower See Figs To Remove MowerFirst Install ANTI-SWAY BAR S To Level Mower Tip of the blade To Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Check Brake To Remove Wheel for Repairs See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Engine dies when Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

960420022, 404402 specifications

The Poulan 960420022,404402 is a well-regarded chainsaw recognized for its blend of performance, durability, and user-friendly features. Manufactured by Poulan, a brand known for its commitment to delivering high-quality outdoor power equipment, this model is designed to meet the needs of both professional landscapers and home users alike.

At the heart of the Poulan 960420022,404402 is its powerful engine. Equipped with a robust two-stroke engine, this chainsaw can produce ample power for cutting through tough wood and tackling various outdoor tasks. The engine is designed with fuel efficiency in mind, allowing users to operate for extended periods without frequent refueling. Its quick-start technology ensures that users can get to work without the frustration of lengthy startup times.

One of the standout features of the Poulan 960420022,404402 is its low-vibration design. This technology not only enhances user comfort during operation but also reduces fatigue, making it ideal for prolonged use. The handle is ergonomically designed to provide a secure grip, ensuring maximum control while cutting.

Another notable characteristic is the chainsaw’s automatic oiler system. This feature provides continuous lubrication to the chain and bar, minimizing wear and ensuring smooth operation. Regular maintenance is simplified, as the tool-free chain tensioning system allows users to easily adjust the chain without the need for additional tools.

Safety is a primary concern for any power tool, and the Poulan 960420022,404402 incorporates several safety features. It includes a chain brake, which acts quickly in the event of kickback, providing an extra layer of protection for users. A transparent fuel tank allows for easy monitoring of fuel levels, further enhancing safety and preventing operational interruptions.

The Poulan 960420022,404402 is compatible with various bar lengths, allowing users to customize their chainsaw for different tasks, from tree trimming to firewood preparation. This adaptiveness makes it a versatile choice for anyone looking to invest in a reliable chainsaw.

In summary, the Poulan 960420022,404402 stands out with its powerful engine, low-vibration design, automatic oiler system, easy chain adjustment, and essential safety features. Whether tackling large projects or performing routine yard maintenance, this chainsaw offers the performance and reliability users expect from a trusted brand.
Top Page Image Contents