Poulan 960 42 00-35, 96042003500 manual Troubleshooting Points, Problem Cause Correction

Page 26

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

CORRECTION

 

 

 

 

 

 

Will not start

1.

Out of fuel.

1.

Fill fuel tank.

 

2.

Engine not “CHOKED” properly.

2.

See “TO START ENGINE” in Operation section.

 

3.

Engine flooded.

3.

Wait several minutes before attempting to start.

 

4.

Bad spark plug.

4.

Replace spark plug.

 

5.

Dirty air filter.

5.

Clean/replace air filter.

 

6.

Dirty fuel filter.

6.

Replace fuel filter.

 

7.

Water in fuel.

7.

Empty fuel tank and carburetor, refill tank with fresh

 

 

 

 

gasoline and replace fuel filter.

 

8.

Loose or damaged wiring.

8.

Check all wiring.

 

9.

Carburetor out of adjustment.

9.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

10.

Engine valves out of adjustment.

10.

Contact an authorized service center/department.

 

 

 

 

 

 

Hard to start

1.

Dirty air filter.

1.

Clean/replace air filter.

 

2.

Bad spark plug.

2.

Replace spark plug.

 

3.

Weak or dead battery.

3.

Recharge or replace battery.

 

4.

Dirty fuel filter.

4.

Replace fuel filter.

 

5.

Stale or dirty fuel.

5.

Empty fuel tank and refill tank with fresh, clean gasoline.

 

6.

Loose or damaged wiring.

6.

Check all wiring.

 

7.

Carburetor out of adjustment.

7.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

8.

Engine valves out of adjustment.

8.

Contact an authorized service center/department.

 

 

 

 

 

 

Engine will not turn over

1.

Clutch/brake pedal not depressed.

1.

Depress clutch/brake pedal.

 

2.

Attachment clutch is engaged.

2.

Disengage attachment clutch.

 

3.

Weak or dead battery.

3.

Recharge or replace battery.

 

4.

Blown fuse.

4.

Replace fuse.

 

5.

Corroded battery terminals.

5.

Clean battery terminals.

 

6.

Loose or damaged wiring.

6.

Check all wiring.

 

7.

Faulty ignition switch.

7.

Check/replace ignition switch.

 

8.

Faulty solenoid or starter.

8.

Check/replace solenoid or starter.

 

9.

Faulty operator presence switch(es).

9.

Contact an authorized service center/department.

 

 

 

 

 

 

Engine clicks but will not

1.

Weak or dead battery.

1.

Recharge or replace battery.

start

2.

Corroded battery terminals.

2.

Clean battery terminals.

 

3.

Loose or damaged wiring.

3.

Check all wiring.

 

4.

Faulty solenoid or starter.

4.

Check/replace solenoid or starter.

 

 

 

 

 

 

Loss of power

1.

Cutting too much grass/too fast.

1.

Raise cutting height/reduce speed.

 

2.

Throttle in “CHOKE” position.

2.

Adjust throttle control.

 

3.

Build-up of grass, leaves and trash under mower.

3.

Clean underside of mower housing.

 

4.

Dirty air filter.

4.

Clean/replace air filter.

 

5.

Low oil level/dirty oil.

5.

Check oil level/change oil.

 

6.

Faulty spark plug.

6.

Clean and regap or change spark plug.

 

7.

Dirty fuel filter.

7.

Replace fuel filter.

 

8.

Stale or dirty fuel.

8.

Empty fuel tank and refill tank with fresh, clean gasoline.

 

9.

Water in fuel.

9.

Empty fuel tank and carburetor, refill tank with fresh

 

 

 

 

gasoline and replace fuel filter.

 

10.

Spark plug wire loose.

10.

Connect and tighten spark plug wire.

 

11.

Dirty engine air screen/fins.

11.

Clean engine air screen/fins.

 

12.

Dirty/clogged muffler.

12.

Clean/replace muffler.

 

13.

Loose or damaged wiring.

13.

Check all wiring.

 

14.

Carburetor out of adjustment.

14.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

15.

Engine valves out of adjustment.

15.

Contact an authorized service center/department.

 

 

 

 

 

 

Excessive vibration

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

2.

Bent blade mandrel.

2.

Replace blade mandrel.

 

3.

Loose/damaged part(s).

3.

Tighten loose part(s). Replace damaged parts.

 

 

 

 

 

 

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents PB19546LT General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Contents of Hardware Pack To Remove Tractor from AssemblyTools Required for Assembly CartonCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Using the Reverse Operation SystemReverse Operation System ROS Before Starting the Engine Mowing Tips Maintenance General RecommendationsTo Sharpen Blade See Fig TractorBlade Removal See Fig Belts BatteryEngine Transaxle CoolingCleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Install belt on engine pulley M, in belt keepers G Precision SIDE-TO-SIDE Adjustment To Level MowerTo Check Brake Belt InstallationTo Replace Mower Drive Belt See Fig To Replace Motion Belt Drive See FigTo Adjust Steering Wheel ALIGN- Ment Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when KEY Part Description Tractor - Model Number PB19546LT 96042003500, Product no 42Wheels and Tires Schematic FuseElectrical 175242 Chassis 194263 Drawbar Drive 162Repair Parts Engine Steering Seat Mower Lift Mower Deck Repair Parts Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXLimited Warranty Policy

960 42 00-35, 96042003500 specifications

The Poulan 96042003500, also known as the Poulan Pro 42cc 2-Cycle Gas Chainsaw, is a reliable and efficient tool designed for both professional landscapers and homeowners alike. This chainsaw stands out in a competitive market due to its blend of power, user-friendly features, and advanced technologies that enhance performance and comfort during operation.

One of the primary features of the Poulan 96042003500 is its powerful 42cc engine. This robust engine is designed to deliver exceptional performance, providing enough power to tackle a variety of cutting tasks, from tree trimming to felling larger trees. The 2-cycle engine is known for its efficiency, ensuring users can perform their tasks with minimal downtime.

The chainsaw is equipped with a 16-inch bar and chain, making it suitable for a wide range of applications. This size strikes a balance, allowing users to handle both small and medium-sized jobs without compromising maneuverability. The chain itself is designed for rapid cutting, contributing to the overall efficiency of the tool.

User comfort and safety have been prioritized in the design of the Poulan 96042003500. It features an ergonomic handle that provides a comfortable grip, reducing fatigue during extended use. Additionally, the chainsaw is equipped with a chain brake for enhanced safety, which stops the chain immediately in case of kickback, protecting the user from potential injuries.

The chainsaw also incorporates advanced technologies like an automatic oiling system, which ensures that the chain and bar remain adequately lubricated during operation. This feature not only extends the life of the saw but also reduces maintenance requirements. The easy-access air filter makes maintenance straightforward, allowing users to clean or replace the filter quickly, promoting better engine performance.

In summary, the Poulan 96042003500 is a versatile and powerful chainsaw that combines robust performance with user-friendly features. Its 42cc engine, lightweight design, and safety features make it an excellent choice for anyone looking to take on outdoor tasks effectively. Whether you're cutting firewood or shaping your landscape, this chainsaw stands as a reliable companion, offering the performance and comfort required for a successful job.
Top Page Image Contents