Poulan 960 42 00-35, 96042003500 Tools Required for Assembly, To Remove Tractor from, Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

INSERT

5/16 HEX BOLT

A socket wrench set will make assembly easier. Standard

wrench sizes are listed.

5/16 LOCK WASHER

(1) 1/2" wrench Utility knife

LARGE FLAT WASHER

 

(2)3/4" wrench Tire pressure gauge Pliers

When right or left hand is mentioned in this manual, it means

 

 

when you are in the operating position (seated behind the

 

 

steering wheel).

 

STEERING

 

 

WHEEL

TO REMOVE TRACTOR FROM

STEERING BOOT

 

CARTON

ADAPTER

 

UNPACK CARTON

 

 

• Remove all accessible loose parts and parts cartons

TABS

 

from carton.

TAB

 

• Cut along dashed lines on all four panels of carton.

 

SLOTS

Remove end panels and lay side panels flat.

 

 

• Check for any additional loose parts or cartons and

EXTENSION SHAFT

 

remove.

 

 

 

LOWER STEERING SHAFT

 

BEFORE REMOVING TRACTOR FROM

 

 

SKID

 

03125

ATTACH STEERING WHEEL (See Fig. 1)

FIG. 1

 

ASSEMBLE EXTENSION SHAFT AND BOOT

 

 

• Slide extension shaft onto lower steering shaft.

INSTALL SEAT (See Figs. 2 and 3)

 

• Place tabs of steering boot over tab slots in dash and

 

push down to secure.

• Remove bolt and flat washer securing seat to cardboard

 

packing and set aside for assembly of seat to tractor.

INSTALL STEERING WHEEL

Remove the cardboard packing and discard.

• Position front wheels of the tractor so they are pointing

• Connect switch to seat.

straight forward.

• Place seat on seat pan so all three (3) bottom pads

• Remove steering wheel adapter from steering wheel

are positioned over large slotted holes in pan.

and slide adapter onto steering shaft extension.

 

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

SEAT

SWITCH

PAD

SLOT

SEAT

PAN

TAPE

WIRING HARNESS

Fig. 2

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PB19546LT General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Contents of Hardware Pack To Remove Tractor from AssemblyTools Required for Assembly CartonCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Using the Reverse Operation System Reverse Operation System ROSTo Operate Mower See Fig Before Starting the Engine Mowing Tips Maintenance General RecommendationsTractor Blade Removal See FigTo Sharpen Blade See Fig Belts BatteryEngine Transaxle CoolingCleaning Service and Adjustments To Install Mower See FigTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G Precision SIDE-TO-SIDE Adjustment To Level MowerTo Check Brake Belt InstallationTo Replace Mower Drive Belt See Fig To Replace Motion Belt Drive See FigTo Adjust Steering Wheel ALIGN- Ment Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Tractor - Model Number PB19546LT 96042003500, Product no 42 Wheels and TiresKEY Part Description Schematic FuseElectrical 175242 Chassis 194263 Drawbar Drive 162Repair Parts Engine Steering Seat Mower Lift Mower Deck Repair Parts Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXLimited Warranty Policy

960 42 00-35, 96042003500 specifications

The Poulan 96042003500, also known as the Poulan Pro 42cc 2-Cycle Gas Chainsaw, is a reliable and efficient tool designed for both professional landscapers and homeowners alike. This chainsaw stands out in a competitive market due to its blend of power, user-friendly features, and advanced technologies that enhance performance and comfort during operation.

One of the primary features of the Poulan 96042003500 is its powerful 42cc engine. This robust engine is designed to deliver exceptional performance, providing enough power to tackle a variety of cutting tasks, from tree trimming to felling larger trees. The 2-cycle engine is known for its efficiency, ensuring users can perform their tasks with minimal downtime.

The chainsaw is equipped with a 16-inch bar and chain, making it suitable for a wide range of applications. This size strikes a balance, allowing users to handle both small and medium-sized jobs without compromising maneuverability. The chain itself is designed for rapid cutting, contributing to the overall efficiency of the tool.

User comfort and safety have been prioritized in the design of the Poulan 96042003500. It features an ergonomic handle that provides a comfortable grip, reducing fatigue during extended use. Additionally, the chainsaw is equipped with a chain brake for enhanced safety, which stops the chain immediately in case of kickback, protecting the user from potential injuries.

The chainsaw also incorporates advanced technologies like an automatic oiling system, which ensures that the chain and bar remain adequately lubricated during operation. This feature not only extends the life of the saw but also reduces maintenance requirements. The easy-access air filter makes maintenance straightforward, allowing users to clean or replace the filter quickly, promoting better engine performance.

In summary, the Poulan 96042003500 is a versatile and powerful chainsaw that combines robust performance with user-friendly features. Its 42cc engine, lightweight design, and safety features make it an excellent choice for anyone looking to take on outdoor tasks effectively. Whether you're cutting firewood or shaping your landscape, this chainsaw stands as a reliable companion, offering the performance and comfort required for a successful job.
Top Page Image Contents