Poulan 96042012600 manual Reverse Operation System ROS, To Operate on Hills, To Transport See Figs

Page 11

OPERATION

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield

(S) in place (See Fig. 10).

S

Fig. 10

REVERSE OPERATION SYSTEM (ROS)

Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

WARNING: Backing up with the attachment clutch en- gaged while mowing is strongly discouraged. Turning the ROS "ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator decides it is necessary to reposition the machine with the attachment engaged. Do not mow in reverse unless absolutely necessary.

USING THE REVERSE OPERATION SYSTEM -

Only use if you are certain no children or other bystanders will enter the mowing area.

•Depress brake pedal all the way down.

•With engine running, turn ignition key counterclockwise to ROS "ON" position.

•Look down and behind before and while backing.

•Slowly depress reverse drive pedal to start movement.

•When use of the ROS is no longer needed, turn the ignition key clockwise to engine "ON" position.

ROS "ON" POSITION

ENGINE "ON" POSITION

 

(NORMAL OPERATING)

02828

TO OPERATE ON HILLS

CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If stopping is absolutely necessary, push brake pedal quickly to brake position and engage parking brake.

•To restart movement, slowly release parking brake and brake pedal.

•Slowly depress appropriate drive pedal to slowest set- ting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 3 and 11)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attachment lift control.

•Pull freewheel control out and down into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

TRANSMISSION ENGAGED

TRANSMISSION DISENGAGED

Fig. 11

TOWING CARTS AND OTHER ATTACHMENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

SERVICE REMINDER/HOUR METER

Service reminder shows the total number of hours the engine has run and flashes to indicate that the engine or mower needs servicing. When service is required, the service reminder will flash for two hours. To service engine and mower, see the Maintenance section of this manual.

NOTE: Service reminder runs when the ignition key is in any position but "STOP". For accurate reading, be sure key remains in the "STOP" position when engine is not running.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents PB23H48YT II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Toremovetractorfromcarton AssemblyTools Required for Assembly Unassembled PartsCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation PEG H Know Your TractorTo USE Throttle Control D See Fig HOW to USE Your TractorTo SET Parking Brake See Fig Stopping See FigTo Stop Mower Blades To Operate MowerTo Transport See Figs Service REMINDER/HOUR MeterReverse Operation System ROS To Operate on HillsTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineRunning Mowing TipsPurge Transmission Schedule MaintenanceMaintenance General RecommendationsBlade Removal See Fig BatteryTractor Blade CareEngine Deck Washout Port See Fig CleaningMuffler IN-LINE Fuel Filter See FigSET Parking Brake Lever and Lower Attachment Lift See Fig To Install Mower and Drive Belt See FigsTo Remove Mower See Fig Slide Mower Under Tractor See Fig ANTI-SWAY BAR STurn Steering Wheel Left and Position Mower See Fig Attach Front Link E See Fig Install Belt on Engine Clutch Pulley M SeeAttach Mower Side Suspension Arms a to Chassis See Fig Attach Rear Lift Links C See FigTo Level Mower Mower Drive Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check BrakeBelt Removal Belt InstallationTo Replace Motion Drive Belt See Fig To Attach Jumper Cables To Start Engine with a Weak Battery See FigTo Remove Wheel See Fig Front Wheel TOE-IN/CAMBERTransmission Cylinders OtherFuel System Engine OILProblem Cause Correction Engine continues To run when operBattery will not Fires when turnLimited Warranty

96042012600, 85-50 specifications

The Poulan 96042012600, often referred to as the 85-50, is a powerful and versatile chainsaw designed to meet the needs of both professionals and avid DIYers. Renowned for its performance and reliability, the 85-50 is suitable for a wide range of cutting tasks, including tree felling, pruning, and firewood preparation.

One of the standout features of the Poulan 85-50 is its robust engine. Powered by a 50cc two-stroke engine, it delivers impressive cutting power while maintaining a relatively lightweight design. This balance between power and weight translates into ease of use, allowing users to operate the chainsaw for extended periods without excessive fatigue. The engine is engineered for efficient fuel usage, contributing to reduced emissions and making it an environmentally friendly choice.

The chainsaw features a 20-inch bar and chain, providing a significant cutting capacity ideal for tackling both small and large trees. The longer bar allows for deeper cuts, making it easier to handle more substantial timber. Additionally, the chain is designed for high performance, ensuring smooth and efficient cuts.

Another key technology in the Poulan 85-50 is its automatic oiler system, which delivers a consistent flow of chain oil to keep the bar and chain lubricated during operation. This feature not only enhances the cutting efficiency but also prolongs the lifespan of the chainsaw by reducing wear and tear on the chain and bar.

Safety is a priority with the Poulan 85-50, which is equipped with a chain brake that can instantly stop the chain in the event of kickback. The design also includes a throttle lock, preventing accidental acceleration and ensuring safe operation. Its anti-vibration technology further reduces operator fatigue, allowing for more control and precision while cutting.

Ergonomics play a significant role in the design of the Poulan 96042012600. The handle is designed to provide a comfortable grip, allowing for better maneuverability, whether you're cutting at ground level or overhead. Additionally, the chainsaw features an easily accessible air filter, simplifying maintenance and ensuring the machine operates at peak efficiency.

In conclusion, the Poulan 96042012600, 85-50, stands out for its combination of power, efficiency, and safety features. With its lightweight design, advanced technology, and ergonomic considerations, it is an excellent choice for anyone seeking a reliable chainsaw for various cutting tasks, making it a valuable tool for both residential and professional use.
Top Page Image Contents