Poulan 96042012600 Unassembled Parts, Tools Required for Assembly, Toremovetractorfromcarton

Page 5

UNASSEMBLED PARTS

Slope Sheet

Key

(1) Oil Drain Tube

(2) Keys

ASSEMBLY

Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

1/2" wrench

Tire pressure gauge

 

(2)

7/16" wrenches

Utility knife

Pliers

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TOREMOVETRACTORFROMCARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton .

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

TO CHECK BATTERY (See Fig. 1)

•Lift hood to raised position.

NOTE: If this battery is put into service after month and year indicated on label (label is located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions).

LABEL

Fig.1

•For battery and battery cable installation see "RE- PLACING BATTERY" in the "Service and Adjustments" section in this manual.

ADJUST SEAT (See Fig. 2)

•Sit in seat.

•Lift up adjustment lever (A) and slide seat until a com- fortable position is reached which allows you to press clutch/brake pedal all the way down.

•Release lever to lock seat in position.

A

Fig. 2

NOTE: You may now roll your tractor off the skid. Follow the instructions below to remove the tractor from the skid.

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

TO ROLL TRACTOR OFF SKID (See Operation section for location and function of controls)

•Raise attachment lift lever to its highest position.

•Releaseparkingbrakebydepressingclutch/brakepedal.

•Place freewheel control in "transmission disengaged" position (See “TO TRANSPORT” in the Operation section of this manual).

•Roll tractor forward off skid.

•Remove banding holding the deflector shield up against tractor.

Continue with the instructions that follow.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents PB23H48YT Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Tools Required for Assembly AssemblyUnassembled Parts ToremovetractorfromcartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation PEG H Know Your TractorTo SET Parking Brake See Fig HOW to USE Your TractorStopping See Fig To USE Throttle Control D See FigTo Stop Mower Blades To Operate MowerReverse Operation System ROS Service REMINDER/HOUR MeterTo Operate on Hills To Transport See FigsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigRunning Mowing TipsPurge Transmission Maintenance MaintenanceGeneral Recommendations ScheduleTractor BatteryBlade Care Blade Removal See FigEngine Muffler CleaningIN-LINE Fuel Filter See Fig Deck Washout Port See FigSET Parking Brake Lever and Lower Attachment Lift See Fig To Install Mower and Drive Belt See FigsTo Remove Mower See Fig Slide Mower Under Tractor See Fig ANTI-SWAY BAR STurn Steering Wheel Left and Position Mower See Fig Attach Mower Side Suspension Arms a to Chassis See Fig Install Belt on Engine Clutch Pulley M SeeAttach Rear Lift Links C See Fig Attach Front Link E See FigTo Replace Mower Blade Drive Belt See Fig Mower Drive Belt InstallationTo Check Brake To Level MowerBelt Removal Belt InstallationTo Replace Motion Drive Belt See Fig To Remove Wheel See Fig To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Attach Jumper CablesTransmission Fuel System OtherEngine OIL CylindersProblem Cause Correction Battery will not To run when operFires when turn Engine continuesLimited Warranty

96042012600, 85-50 specifications

The Poulan 96042012600, often referred to as the 85-50, is a powerful and versatile chainsaw designed to meet the needs of both professionals and avid DIYers. Renowned for its performance and reliability, the 85-50 is suitable for a wide range of cutting tasks, including tree felling, pruning, and firewood preparation.

One of the standout features of the Poulan 85-50 is its robust engine. Powered by a 50cc two-stroke engine, it delivers impressive cutting power while maintaining a relatively lightweight design. This balance between power and weight translates into ease of use, allowing users to operate the chainsaw for extended periods without excessive fatigue. The engine is engineered for efficient fuel usage, contributing to reduced emissions and making it an environmentally friendly choice.

The chainsaw features a 20-inch bar and chain, providing a significant cutting capacity ideal for tackling both small and large trees. The longer bar allows for deeper cuts, making it easier to handle more substantial timber. Additionally, the chain is designed for high performance, ensuring smooth and efficient cuts.

Another key technology in the Poulan 85-50 is its automatic oiler system, which delivers a consistent flow of chain oil to keep the bar and chain lubricated during operation. This feature not only enhances the cutting efficiency but also prolongs the lifespan of the chainsaw by reducing wear and tear on the chain and bar.

Safety is a priority with the Poulan 85-50, which is equipped with a chain brake that can instantly stop the chain in the event of kickback. The design also includes a throttle lock, preventing accidental acceleration and ensuring safe operation. Its anti-vibration technology further reduces operator fatigue, allowing for more control and precision while cutting.

Ergonomics play a significant role in the design of the Poulan 96042012600. The handle is designed to provide a comfortable grip, allowing for better maneuverability, whether you're cutting at ground level or overhead. Additionally, the chainsaw features an easily accessible air filter, simplifying maintenance and ensuring the machine operates at peak efficiency.

In conclusion, the Poulan 96042012600, 85-50, stands out for its combination of power, efficiency, and safety features. With its lightweight design, advanced technology, and ergonomic considerations, it is an excellent choice for anyone seeking a reliable chainsaw for various cutting tasks, making it a valuable tool for both residential and professional use.
Top Page Image Contents