Poulan 85-50, 96042012600 manual Transmission

Page 24

SERVICE AND ADJUSTMENTS

REPLACING BATTERY (See Fig. 40)

WARNING: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding.

Lift hood to raised position.

Remove terminal cover.

Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.

Install new battery with terminals in same position as old battery.

Reinstall terminal cover.

First connect RED battery cable to positive (+) battery terminal with bolt and nut as shown. Tighten securely.

Connect BLACK grounding cable to negative (-) battery terminal with remaining bolt and nut. Tighten securely

Close hood.

NEGATIVE (BLACK)

CABLE

TERMINAL

COVER

POSITIVE (RED)

CABLE

Fig. 40

TO REPLACE HEADLIGHT BULB

Raise hood.

Pull bulb holder out of the hole in the backside of the grill.

Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

Check wiring.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 38)

Raise hood.

Unsnap headlight wire connector.

Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

05000

Fig. 41

TRANSMISSION

REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and beforeoperatingthetractor. See“PURGETRANSMISSION” in the Operation section of this manual.

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and adjust- ment should not be necessary. If adjustment is necessary, see engne manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

24

Image 24
Contents PB23H48YT Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Assembly Tools Required for AssemblyUnassembled Parts ToremovetractorfromcartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor PEG HHOW to USE Your Tractor To SET Parking Brake See FigStopping See Fig To USE Throttle Control D See FigTo Operate Mower To Stop Mower BladesService REMINDER/HOUR Meter Reverse Operation System ROSTo Operate on Hills To Transport See FigsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionRunning Maintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBlade Care Blade Removal See FigEngine Cleaning MufflerIN-LINE Fuel Filter See Fig Deck Washout Port See FigTo Install Mower and Drive Belt See Figs To Remove Mower See FigSET Parking Brake Lever and Lower Attachment Lift See Fig ANTI-SWAY BAR S Turn Steering Wheel Left and Position Mower See FigSlide Mower Under Tractor See Fig Install Belt on Engine Clutch Pulley M See Attach Mower Side Suspension Arms a to Chassis See FigAttach Rear Lift Links C See Fig Attach Front Link E See FigMower Drive Belt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Level MowerBelt Installation To Replace Motion Drive Belt See FigBelt Removal To Start Engine with a Weak Battery See Fig To Remove Wheel See FigFront Wheel TOE-IN/CAMBER To Attach Jumper CablesTransmission Other Fuel SystemEngine OIL CylindersProblem Cause Correction To run when oper Battery will notFires when turn Engine continuesLimited Warranty

96042012600, 85-50 specifications

The Poulan 96042012600, often referred to as the 85-50, is a powerful and versatile chainsaw designed to meet the needs of both professionals and avid DIYers. Renowned for its performance and reliability, the 85-50 is suitable for a wide range of cutting tasks, including tree felling, pruning, and firewood preparation.

One of the standout features of the Poulan 85-50 is its robust engine. Powered by a 50cc two-stroke engine, it delivers impressive cutting power while maintaining a relatively lightweight design. This balance between power and weight translates into ease of use, allowing users to operate the chainsaw for extended periods without excessive fatigue. The engine is engineered for efficient fuel usage, contributing to reduced emissions and making it an environmentally friendly choice.

The chainsaw features a 20-inch bar and chain, providing a significant cutting capacity ideal for tackling both small and large trees. The longer bar allows for deeper cuts, making it easier to handle more substantial timber. Additionally, the chain is designed for high performance, ensuring smooth and efficient cuts.

Another key technology in the Poulan 85-50 is its automatic oiler system, which delivers a consistent flow of chain oil to keep the bar and chain lubricated during operation. This feature not only enhances the cutting efficiency but also prolongs the lifespan of the chainsaw by reducing wear and tear on the chain and bar.

Safety is a priority with the Poulan 85-50, which is equipped with a chain brake that can instantly stop the chain in the event of kickback. The design also includes a throttle lock, preventing accidental acceleration and ensuring safe operation. Its anti-vibration technology further reduces operator fatigue, allowing for more control and precision while cutting.

Ergonomics play a significant role in the design of the Poulan 96042012600. The handle is designed to provide a comfortable grip, allowing for better maneuverability, whether you're cutting at ground level or overhead. Additionally, the chainsaw features an easily accessible air filter, simplifying maintenance and ensuring the machine operates at peak efficiency.

In conclusion, the Poulan 96042012600, 85-50, stands out for its combination of power, efficiency, and safety features. With its lightweight design, advanced technology, and ergonomic considerations, it is an excellent choice for anyone seeking a reliable chainsaw for various cutting tasks, making it a valuable tool for both residential and professional use.