Poulan 85-50, 96042012600 manual Before Starting the Engine, Check Engine OIL Level, ADD Gasoline

Page 12

OPERATION

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

•Check engine oil with tractor on level ground.

•Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Maintenance section of this manual).

•To change engine oil, see the Maintenance section in this manual.

ADD GASOLINE

•Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW 32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP ENSURE GOOD COLD WEATHER STARTING.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 3)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Be sure freewheel control is in the transmission engaged position.

•Sit on seat in operating position, depress brake pedal and set parking brake.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to choke position.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry.

WARM WEATHER STARTING (50°F/10°C and above)

•When engine starts, move the throttle control to the fast position.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50°F/10°C and below)

•When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast posi- tion. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Release the parking brake and let the brake slowly return to operating position.

•Allow one minute for transmission to warm up. This can be done during the engine warm up period.

•Theattachmentscanalsobeusedduringtheenginewarm- up period after the transmission has been warmed up.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32°F/0°C) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjust- ments section of this manual.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PB23H48YT Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Assembly Tools Required for AssemblyUnassembled Parts ToremovetractorfromcartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor PEG HHOW to USE Your Tractor To SET Parking Brake See FigStopping See Fig To USE Throttle Control D See FigTo Operate Mower To Stop Mower BladesService REMINDER/HOUR Meter Reverse Operation System ROSTo Operate on Hills To Transport See FigsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionRunning Maintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBlade Care Blade Removal See FigEngine Cleaning MufflerIN-LINE Fuel Filter See Fig Deck Washout Port See FigTo Install Mower and Drive Belt See Figs To Remove Mower See FigSET Parking Brake Lever and Lower Attachment Lift See Fig ANTI-SWAY BAR S Turn Steering Wheel Left and Position Mower See FigSlide Mower Under Tractor See Fig Install Belt on Engine Clutch Pulley M See Attach Mower Side Suspension Arms a to Chassis See FigAttach Rear Lift Links C See Fig Attach Front Link E See FigMower Drive Belt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Level MowerBelt Installation To Replace Motion Drive Belt See FigBelt Removal To Start Engine with a Weak Battery See Fig To Remove Wheel See FigFront Wheel TOE-IN/CAMBER To Attach Jumper CablesTransmission Other Fuel SystemEngine OIL CylindersProblem Cause Correction To run when oper Battery will notFires when turn Engine continuesLimited Warranty

96042012600, 85-50 specifications

The Poulan 96042012600, often referred to as the 85-50, is a powerful and versatile chainsaw designed to meet the needs of both professionals and avid DIYers. Renowned for its performance and reliability, the 85-50 is suitable for a wide range of cutting tasks, including tree felling, pruning, and firewood preparation.

One of the standout features of the Poulan 85-50 is its robust engine. Powered by a 50cc two-stroke engine, it delivers impressive cutting power while maintaining a relatively lightweight design. This balance between power and weight translates into ease of use, allowing users to operate the chainsaw for extended periods without excessive fatigue. The engine is engineered for efficient fuel usage, contributing to reduced emissions and making it an environmentally friendly choice.

The chainsaw features a 20-inch bar and chain, providing a significant cutting capacity ideal for tackling both small and large trees. The longer bar allows for deeper cuts, making it easier to handle more substantial timber. Additionally, the chain is designed for high performance, ensuring smooth and efficient cuts.

Another key technology in the Poulan 85-50 is its automatic oiler system, which delivers a consistent flow of chain oil to keep the bar and chain lubricated during operation. This feature not only enhances the cutting efficiency but also prolongs the lifespan of the chainsaw by reducing wear and tear on the chain and bar.

Safety is a priority with the Poulan 85-50, which is equipped with a chain brake that can instantly stop the chain in the event of kickback. The design also includes a throttle lock, preventing accidental acceleration and ensuring safe operation. Its anti-vibration technology further reduces operator fatigue, allowing for more control and precision while cutting.

Ergonomics play a significant role in the design of the Poulan 96042012600. The handle is designed to provide a comfortable grip, allowing for better maneuverability, whether you're cutting at ground level or overhead. Additionally, the chainsaw features an easily accessible air filter, simplifying maintenance and ensuring the machine operates at peak efficiency.

In conclusion, the Poulan 96042012600, 85-50, stands out for its combination of power, efficiency, and safety features. With its lightweight design, advanced technology, and ergonomic considerations, it is an excellent choice for anyone seeking a reliable chainsaw for various cutting tasks, making it a valuable tool for both residential and professional use.
Top Page Image Contents