Poulan 532 43 88-98, 96018000400 manual Tractor, Blade Care, Blade Removal See Fig, Battery

Page 16

MAINTENANCE

TRACTOR

Always observe safety rules when performing any maintenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See the sides of tires for proper PSI).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS) (See Fig. 8)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

 

 

 

 

 

 

 

 

 

 

02828

ROS "ON"

ENGINE "ON" POSITION

POSITION

(NORMAL OPERATING)

 

 

 

 

 

 

Fig. 8

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

CAUTION: Use only a replacement blade ap- proved by the manufacturer of your tractor. Using a blade not approved by the manu- facturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 9)

•Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new or resharpened blade with stamped "THIS SIDE UP" facing deck and mandrel assembly.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED.

MANDREL ASSEMBLY

 

BLADE

BLADE BOLT

STAR

(SPECIAL)

CENTER HOLE

Fig. 9

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE:Theoriginalequipmentbatteryonyourtractorismain- tenance free. Do not attempt to open or remove caps or cov- ers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

•Raise seat.

•Disconnect BLACK battery cable first then RED bat- tery cable and remove battery from tractor.

•Rinse the battery with plain water and dry.

•Clean terminals and battery cable ends with wire brush until bright.

•Coat terminals with grease or petroleum jelly.

•Reinstall battery (See “REPLACING BATTERY" in the Service and Adjustments section of this manual).

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents PO17542LT ModelSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Steering WheelAssembly Tools Required for AssemblyToremovetractorfromcarton Before Removing Tractor from SkidTo Check Battery See Fig Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsChecklist Operation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Operate on HillsTo Transport Towing Carts and Other ATTACH- MentsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Maintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBlade Care Blade Removal See FigEngine Engine Cooling System See Fig CleaningIN-LINE Fuel Filter See Fig To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check Brake To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionExcessive Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

96018000400, 532 43 88-98 specifications

The Poulan 532 43 88-98 (96018000400) is a versatile and robust outdoor power equipment component designed specifically for lawn care and maintenance. Recognized for its reliability, this item is an essential addition to any landscaping toolkit, ensuring that users can tackle a wide range of tasks with ease.

One of the standout features of the Poulan 532 43 88-98 model is its powerful engine. This engine is designed to handle demanding jobs effectively, providing ample power to cut through thick grass and other vegetation without bogging down. The engine's efficiency also ensures that users can accomplish more in less time, making it perfect for both residential and commercial use.

The design of the Poulan 532 43 88-98 is another aspect that sets it apart. Engineered for user comfort and control, the equipment features an ergonomic handle that reduces fatigue during extended use. Its lightweight construction makes it easy to maneuver, even in tight spaces or on uneven terrain. This blend of comfort and functionality allows for prolonged use without compromising performance.

In terms of technology, the Poulan 532 43 88-98 incorporates advanced cutting systems that ensure clean and precise cuts. The sharp blades are crafted from high-quality materials, promising durability and longevity. Additionally, the model's adjustable cutting heights provide flexibility, allowing users to customize their mowing experience based on their specific lawn care needs.

Safety is another priority with the Poulan 532 43 88-98. This model comes equipped with several safety features, including a guard that protects the user from debris and a quick-stop function that halts the blades immediately when needed. These features are especially important for reducing the risks associated with outdoor power equipment usage.

Overall, the Poulan 532 43 88-98 (96018000400) emerges as a capable solution for anyone in need of a reliable and powerful product for lawn care. Its blend of efficiency, safety, and user-friendly design makes it suitable for various settings, from traditional home lawns to professional landscaping operations. Whether you're a homeowner taking on DIY yard projects or a contractor maintaining expansive properties, the Poulan 532 43 88-98 is engineered to meet diverse lawn care demands effectively.
Top Page Image Contents