Poulan 532 43 88-98, 96018000400 manual Transaxle Gear Shift Lever NEUTRAL- Adjustment See Fig

Page 22

SERVICE AND ADJUSTMENTS

TRANSAXLE GEAR SHIFT LEVER NEUTRAL- ADJUSTMENT (See Fig. 21)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) posi- tion.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

 

NEUTRAL

GEARSHIFT LEVER

LOCK GATE

 

 

ADJUSTMENT

 

BOLT

Fig. 21

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

Fig. 22

TO START ENGINE WITH A WEAK BATTERY (See Fig. 23)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 22)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

22

Fig. 23

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PO17542LT ModelGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Steering WheelToremovetractorfromcarton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Deck Levelness To Check Battery See FigCheck Tire Pressure Check for Proper Position of ALL BeltsChecklist Operation Know Your Tractor HOW to USE Your Tractor To Transport Reverse Operation System ROSTo Operate on Hills Towing Carts and Other ATTACH- MentsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips General Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine Engine Cooling System See Fig CleaningIN-LINE Fuel Filter See Fig To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check Brake To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionExcessive Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

96018000400, 532 43 88-98 specifications

The Poulan 532 43 88-98 (96018000400) is a versatile and robust outdoor power equipment component designed specifically for lawn care and maintenance. Recognized for its reliability, this item is an essential addition to any landscaping toolkit, ensuring that users can tackle a wide range of tasks with ease.

One of the standout features of the Poulan 532 43 88-98 model is its powerful engine. This engine is designed to handle demanding jobs effectively, providing ample power to cut through thick grass and other vegetation without bogging down. The engine's efficiency also ensures that users can accomplish more in less time, making it perfect for both residential and commercial use.

The design of the Poulan 532 43 88-98 is another aspect that sets it apart. Engineered for user comfort and control, the equipment features an ergonomic handle that reduces fatigue during extended use. Its lightweight construction makes it easy to maneuver, even in tight spaces or on uneven terrain. This blend of comfort and functionality allows for prolonged use without compromising performance.

In terms of technology, the Poulan 532 43 88-98 incorporates advanced cutting systems that ensure clean and precise cuts. The sharp blades are crafted from high-quality materials, promising durability and longevity. Additionally, the model's adjustable cutting heights provide flexibility, allowing users to customize their mowing experience based on their specific lawn care needs.

Safety is another priority with the Poulan 532 43 88-98. This model comes equipped with several safety features, including a guard that protects the user from debris and a quick-stop function that halts the blades immediately when needed. These features are especially important for reducing the risks associated with outdoor power equipment usage.

Overall, the Poulan 532 43 88-98 (96018000400) emerges as a capable solution for anyone in need of a reliable and powerful product for lawn care. Its blend of efficiency, safety, and user-friendly design makes it suitable for various settings, from traditional home lawns to professional landscaping operations. Whether you're a homeowner taking on DIY yard projects or a contractor maintaining expansive properties, the Poulan 532 43 88-98 is engineered to meet diverse lawn care demands effectively.
Top Page Image Contents