Poulan 532 43 88-98 Tools Required for Assembly, Toremovetractorfromcarton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

5/16" wrench

Utility knife

(2)

7/16" wrenches

Tire pressure gauge

(2) 1/2" wrenches

Pliers

(1)

9/16" wrench

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TOREMOVETRACTORFROMCARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton .

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

TO INSTALL STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, lock washer, hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

5/16 HEX BOLT

5/16 LOCK WASHER

LARGE FLAT

WASHER

STEERING

 

WHEEL

STEERING

 

 

BOOT

ADAPTER

 

 

EXTENSION

 

SHAFT

LOWER

STEERING

SHAFT

Fig. 1

INSTALL SEAT (See Fig. 2

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan and assemble shoulder bolt. Tighten shoulder bolt securely.

•Assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PO17542LT ModelGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Steering WheelToremovetractorfromcarton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Deck Levelness To Check Battery See FigCheck Tire Pressure Check for Proper Position of ALL BeltsChecklist Operation Know Your Tractor HOW to USE Your Tractor To Transport Reverse Operation System ROSTo Operate on Hills Towing Carts and Other ATTACH- MentsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips General Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine Cleaning Engine Cooling System See FigIN-LINE Fuel Filter See Fig Service and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Blade Drive Belt See Fig To Check BrakeTo Replace Motion Drive Belt See Fig To Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionExcessive Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

96018000400, 532 43 88-98 specifications

The Poulan 532 43 88-98 (96018000400) is a versatile and robust outdoor power equipment component designed specifically for lawn care and maintenance. Recognized for its reliability, this item is an essential addition to any landscaping toolkit, ensuring that users can tackle a wide range of tasks with ease.

One of the standout features of the Poulan 532 43 88-98 model is its powerful engine. This engine is designed to handle demanding jobs effectively, providing ample power to cut through thick grass and other vegetation without bogging down. The engine's efficiency also ensures that users can accomplish more in less time, making it perfect for both residential and commercial use.

The design of the Poulan 532 43 88-98 is another aspect that sets it apart. Engineered for user comfort and control, the equipment features an ergonomic handle that reduces fatigue during extended use. Its lightweight construction makes it easy to maneuver, even in tight spaces or on uneven terrain. This blend of comfort and functionality allows for prolonged use without compromising performance.

In terms of technology, the Poulan 532 43 88-98 incorporates advanced cutting systems that ensure clean and precise cuts. The sharp blades are crafted from high-quality materials, promising durability and longevity. Additionally, the model's adjustable cutting heights provide flexibility, allowing users to customize their mowing experience based on their specific lawn care needs.

Safety is another priority with the Poulan 532 43 88-98. This model comes equipped with several safety features, including a guard that protects the user from debris and a quick-stop function that halts the blades immediately when needed. These features are especially important for reducing the risks associated with outdoor power equipment usage.

Overall, the Poulan 532 43 88-98 (96018000400) emerges as a capable solution for anyone in need of a reliable and powerful product for lawn care. Its blend of efficiency, safety, and user-friendly design makes it suitable for various settings, from traditional home lawns to professional landscaping operations. Whether you're a homeowner taking on DIY yard projects or a contractor maintaining expansive properties, the Poulan 532 43 88-98 is engineered to meet diverse lawn care demands effectively.
Top Page Image Contents