Poulan 96042011100, 434534 To Adjust Mower Cutting Height See Fig, To Adjust Gauge Wheels See Fig

Page 13

OPERATION

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 21)

The position of the attachment lift lever (A) determines the cutting height.

A

T

Fig. 21

•Put attachment lift lever in desired cutting height slot.

•Slide pointer tab (T) to desired cutting height as a reminder for next time you mow.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2" during the cool season and to over 3" during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 22)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole as shown and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

Fig. 22

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut (see "TO ADJUST MOWER CUTTING HEIGHT")

•Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES

Disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield

(S) in place (See Fig. 23).

S

Fig. 23

REVERSE OPERATION SYSTEM (ROS)

Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

WARNING: Backing up with the attachment clutch en- gaged while mowing is strongly discouraged. Turning the ROS "ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator decides it is necessary to reposition the machine with the attachment engaged. Do not mow in reverse unless absolutely necessary.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents PBGT26H54 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Rear 3/16 Lift Link Shoulder Bolt 1/4 O.D Unassembled PartsOil Drain Tube 4 O.DTools Required for Assembly AssemblyToremovetractorfromcarton Before Removing Tractor from SkidTurn Steering Wheel Left and Position Mower See Fig Install ANTI-SWAY BAR S if Equipped SeeANTI-SWAY BAR S Attach Rear Lift Links C See Fig Attach Mower Side Suspension Arms a to Chassis See FigAttach Front Link E See Fig Check Tire Pressure Install Belt on Engine Clutch Pulley M SeeCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigTo Operate Mower To Stop Mower BladesBefore Starting the Engine Service REMINDER/HOUR MeterTo Operate on Hills Check Engine OIL LevelPurge Transmission To Start Engine See FigAutomatic Transmission Warm UP Mowing Tips Maintenance MaintenanceGeneral Recommendations ScheduleTractor BatteryBlade Care Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningDeck Washout Port See Fig To Install Mower Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Blade Drive Belt See FigTo Level Mower Belt Installation Transaxle Motion Control Lever Neutral Adjustment See FigTo Replace Motion Drive Belt See Fig To Check BrakeReplacing Battery See Fig To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel See FigTransmission Other StorageFuel System Engine OILProblem Cause Correction TroubleshootingBattery will not To run when operFires when turn Engine continuesOnly Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationLimited Warranty

434534, 96042011100 specifications

The Poulan 96042011100,434534 is a powerful and versatile outdoor equipment designed to make yard work efficient and manageable. Known for its robust performance, this machine is a testament to Poulan’s commitment to quality and reliability. It comes equipped with a range of features, technologies, and characteristics that make it stand out in the crowded field of outdoor power tools.

One of the main features of the Poulan 96042011100 is its powerful engine. This model is equipped with a high-performance motor that provides ample power for various yard tasks, including trimming, edging, and maintaining small to medium-sized lawns. The engine is designed for fuel efficiency, allowing users to complete tasks without frequent refueling, which enhances productivity.

The design of the Poulan 96042011100 emphasizes user comfort. It features an adjustable handle that can be modified to suit different user heights and preferences, ensuring that operators can work for extended periods without experiencing discomfort. Additionally, the lightweight construction of the machine makes it easy to maneuver around obstacles in the yard, reducing strain on the user.

In terms of technology, the Poulan 96042011100 utilizes advanced cutting systems that enable clean and precise cuts. The sharp blades are engineered to handle a variety of grass types and thicknesses, making the machine versatile enough to tackle different yard conditions. Furthermore, the easy-start system is a notable feature that promotes hassle-free operation, allowing users to start the machine with minimal effort.

The Poulan 96042011100 also stands out for its safety features. It includes a protective guard that shields the operator from debris and flying grass clippings, significantly enhancing user safety during operation. The machine's design incorporates safety switches to prevent accidental starts, ensuring a safer working environment.

Lastly, durability is a key characteristic of the Poulan 96042011100. Built with high-quality materials, this outdoor equipment is designed to withstand the rigors of outdoor use. Its resilient components ensure that the machine can operate effectively season after season, making it a valuable addition to any homeowner's toolkit.

In summary, the Poulan 96042011100,434534 is a well-rounded outdoor tool that combines power, comfort, and safety features to meet the needs of homeowners and gardeners. Its advanced technologies and durable design make it a reliable choice for maintaining a pristine yard, ensuring a satisfying user experience every time.
Top Page Image Contents