Poulan 532 43 88-78 Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 18

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

Depress brake pedal fully and set parking brake.

Place motion control lever in neutral position.

Place attachment clutch in “DISENGAGED” position.

Turn ignition key to “STOP” and remove key.

Make sure the blades and all moving parts have completely stopped.

Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TO REMOVE MOWER (See Fig. 21)

Place attachment clutch in “DISENGAGED” position.

Lower attachment lift lever to its lowest position.

Roll belt off engine pulley (M) and belt keepers (G).

Remove retainer spring (K), slide collar (L) off and push housing guide (P) out of bracket.

Remove clutch cable spring (Q) from idler arm (R).

Disconnect front link (E) from mower - remove retainer spring and washer.

Go to either side of mower and disconnect mower suspension arm (A) from chassis pin (B) and rear lift link (C) from rear mower bracket (D) - remove retainer springs and washers.

CAUTION: AFTER REAR LIFT LINKS

ARE DISCONNECTED, THE ATTACH-

MENT LIFT LEVER WILL BE SPRING

LOADED. HAVE A TIGHT GRIP ON LIFT

LEVER WHEN CHANGING POSITION

OF THE LEVER.

Slide mower out from under right side of tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONT LINK (E) AND REAR LIFT LINKS

(C)FROM TRACTOR AND HOOK THE CLUTCH SPRING

(Q)INTO THE CABLE GUIDE ON FRONT EDGE OF LOWER DASH.

TO INSTALL MOWER (See Fig. 22-26)

Be sure tractor is on level surface and engage parking brake.

Lower attachment lift lever to its lowest position.

CAUTION: LIFT LEVER IS SPRING

LOADED. HAVE A TIGHT GRIP ON

LIFT LEVER, LOWER IT SLOWLY AND

ENGAGE IN LOWEST POSITION.

NOTE: Be sure mower side suspension arms (A) are point- ing forward before sliding mower under tractor.

Slide mower under tractor until it is centered under tractor.

G MF

RG

Q

P

A E

B

C

K

D

 

L

Fig. 21

 

 

18

Image 18
Contents PB20H42YT General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationService III. ChildrenIV. Towing Table of Contents To Remove Tractor from Carton Tools Required for AssemblyUnassembled Parts Before Removing Tractor from SkidCheck Deck Levelness AssemblyCheck Tire Pressure Check for Proper Position of BeltsOperation Know Your Tractor Stopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control See FigReverse Operation System ROS To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerBefore Starting the Engine To Start Engine See Fig Purge TransmissionAutomatic Transmission Warm UP Mowing Tips General Recommendations MaintenanceMaintenance ScheduleBattery TractorBlade Removal See Fig Engine Cleaning IN-LINE Fuel Filter See FigDeck Washout Port See Fig Service and Adjustments To Install Mower See FigTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Remove Wheel See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Fuel System StorageOther Engine OILTroubleshooting Problem Cause CorrectionTroubleshooting Points Suggested Guide for Sighting Slopes for Safe Operation Limited Warranty

96048000500, 532 43 88-78 specifications

The Poulan 532 43 88-78,96048000500 is an innovative lawn mower accessory designed to enhance lawn maintenance efficiency. Known for its robust build quality and reliability, this piece of equipment is favored by both homeowners and professional landscapers.

One of the standout features of the Poulan 532 43 88-78,96048000500 is its compatibility with a variety of Poulan lawn mowers. This ensures that users can easily integrate this accessory into their existing lawn care systems. The design focuses on versatility, allowing it to work seamlessly with different models, making it a versatile addition to any green space toolkit.

Equipped with a powerful engine, the Poulan 532 features advanced technologies that optimize performance. The cutting system is designed with precision blades that deliver clean and even cuts. This not only enhances the appearance of the lawn but also promotes healthier grass growth by reducing stress on the plants.

Durability is a key characteristic of this product. Constructed from high-grade materials, the Poulan 532 is built to withstand the rigors of regular use. Its rugged design minimizes wear and tear, ensuring longevity and reliability, even in challenging conditions.

This model also incorporates easy-start technology, which allows users to start the machine with minimal effort. This feature is particularly useful for those who may struggle with traditional pull-start mechanisms. Furthermore, the user-friendly controls make operation straightforward, appealing to both novices and experienced users alike.

In addition, the Poulan 532 43 88-78,96048000500 offers adjustable cutting height settings, allowing users to customize the length of grass cut to their preference. This feature grants lawn caretakers the flexibility to maintain their lawns according to seasonal needs or individual aesthetic choices.

Maintenance is made easy with the Poulan 532, thanks to its accessible design. Routine checks and part replacements can be conducted without significant hassle, promoting a longer lifespan for the machine. Users appreciate that they can spend less time on upkeep and more time enjoying their beautifully manicured lawns.

Overall, the Poulan 532 43 88-78,96048000500 stands out in the market for its combination of powerful performance, user-friendly features, and durable construction. Perfect for anyone who values quality lawn equipment, this accessory is sure to meet the demands of modern lawn care while providing exceptional results.