Poulan 96042010900, PB23H48YT Before Starting the Engine, Check Engine OIL Level, ADD Gasoline

Page 12

OPERATION

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

Check engine oil with tractor on level ground.

Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Maintenance section of this manual).

To change engine oil, see the Maintenance section in this manual.

ADD GASOLINE

Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW 32°F (0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP ENSURE GOOD COLD WEATHER STARTING.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract mois- ture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 3)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

Be sure freewheel control is in the transmission engaged position.

Sit on seat in operating position, depress brake pedal and set parking brake.

Move attachment clutch to “DISENGAGED” position.

Move throttle control to choke position.

NOTE: Before starting, read the warm and cold starting procedures below.

Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry.

WARM WEATHER STARTING (50°F/10°C and above)

When engine starts, move the throttle control to the fast position.

The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50°F/10°C and below)

When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast posi- tion. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

Before driving the unit in cold weather, the transmission should be warmed up as follows:

Be sure the tractor is on level ground.

Release the parking brake and let the brake slowly return to operating position.

Allow one minute for transmission to warm up. This can be done during the engine warm up period.

Theattachmentscanalsobeusedduringtheenginewarm- up period after the transmission has been warmed up.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32° F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

12

Image 12
Contents PB23H48YT Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Assembly Tools Required for AssemblyUnassembled Parts To Remove Tractor from CartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To SET Parking Brake See FigStopping See Fig To USE Throttle Control D See FigTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigTo Move Forward and Backward See Fig To USE Cruise Control J See FigService REMINDER/HOUR Meter To Operate MowerReverse Operation System ROS To Operate on HillsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionMaintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBlade Care Blade Removal See FigEngine Cleaning MufflerIN-LINE Fuel Filter See Fig Deck Washout Port See FigService and Adjustments To Install Mower See FigsTo Remove Mower See Fig First Install ANTI-SWAY BAR S M F Visual SIDE-TO-SIDE Adjustment See Fig Precision SIDE-TO-SIDE Adjustment See FigTo Level Mower Turn nut right Turn nut left To raise mowerTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigTo Check Brake Front Wheel TOE-IN/CAMBERTransmission Storage OtherFuel System Engine OILTroubleshooting Problem Cause CorrectionTo run when oper Battery will notFires when turn Engine continuesService Notes Suggested Guide for Sighting Slopes for Safe Operation Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Degrés MAX ’ENTRETIEN Remarques Dépannage DE Guide Correction Cause ProblèmePuissance de Entreposage Reglages ET Revision MoteurRossage AVANT/CAR Roues DES ConvergenceLA DE L’ALIGNEMENT Régler Pour Fig la Voir Faible RietebatFig la Voir D’ENTRAÎNEMENT Courroie Acer Rempl PourFig la Voir Tondeuse LA DE Lame Freins LES Vérifier Pour LA DE Courroie LA Remplacer PourTondeuse LA Niveau LE Ajuster Pour 33 .Fig32 .Fig 31 .FigAvant l’embrayage de poulie la sur courroie la Installez 29 .Fig28 .Fig 27 .Fig26 .FIG 25 .FIG24 .FIG 23 .FIGTondeuse LA Installer 29 20 .Figs les Voir18 20 .Fig 21 .Fig Stationnement de frein le actionnez et niveauLigne EN Installé D’ESSENCE Filtre EntretienFig La Voir Coupe DE Plateau DU Lavage DE Raccord Silencieux’ALLUMAGE Bougie Ventilation DE Système’AIR Tamis LE Nettoyer AIR À FiltreFig la Voir Lame LA Enlever Lames DES EntretienPneus Frein DU FonctionnementUtilisation Chaque Avant Lubrification DE TableauAvant ET Réinstallation LA Après Purgée Être UtilisationTransmission LA Purger 13 .Fig’ESSENCE Réservoir LE Remplir Moteur DU D’HUILE Niveau LE VérifierAccessoires Autres ET Charrettes DES Remorquer Pour ROS Arrière Marche EN Fonctionnement DE SystèmeTracteur LE Transporter Pour Pentes LES Dans Utiliser PourTondeuse DE Lames LES Arrêter Pour Jauge DE Roues LES Régler PourFig la Voir J Vitesse DE Régulateur LE Utiliser Comment Tondeuse LA Utiliser PourGAZ DES Commande LA Utiliser Pour Fig la Voir Arrêter PourFig la Voir Mentnetionsta DE Frein LE Embrayée Pour Entraînement’ACCESSOIRE D’EMBRAYAGE Interrupteur E Frein DE Pédale Montage Montées NON Piéces Desmancom des fonction la etTionsec la Voir Rouler Faisant LE EN TE Fig la SIÈGEVoir LE Régler PourUtilisation MontageClient DU Responsabilités Produit DE SpécificationsSécurité DE Règles Tracteurs des sécurité touteEnfants En l’utilisation pour ConseilsAvertissement Tracteurs des sécurité toute en l’utilisation pour ConseilsPentes LES Dans Fonctionnement Général FonctionnementCom.pro-poulan.www web site notre Visitez Avertissement