Poulan DPR22H46STA owner manual To Adjust Brake See Fig, To Replace Motion Drive Belt See Fig

Page 23

SERVICE AND ADJUSTMENTS

L.H. MANDREL

MOWER BLADE DRIVE BELT CENTER MANDREL

IDLER PULLEY

R.H.

MANDREL

COVER

SECONDARY IDLER ARM

SPRING SWAY-BAR

BRACKET SCREW

FIG. 28

TO ADJUST BRAKE (See Fig. 29)

Your tractor is equipped with an adjustable brake system which is mounted on the side of the transaxle.

If tractor requires more than six (6) feet stopping distance at high speed in highest gear on a level dry concrete or paved surface, then brake must be adjusted.

•Depress clutch/brake pedal and engage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-9/16", loosen jam nut and turn nut “A” until distance becomes 1-9/16". Retighten jam nut against nut “A”.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than six (6) feet in highest gear, further maintenance is necessary. Contact your nearest au- thorized service center/department.

WITH PARKING

 

NUT

 

BRAKE

1-9/16"

“A”

JAM NUT

 

 

“ENGAGED”

OPERATING

ARM

DO NOT TOUCH THIS NUT. IF FURTHER BRAKE ADJUST- MENT IS NECESSARY CONTACT YOUR NEAREST AUTHO- RIZED SERVICE CENTER/DEPARTMENT

FIG. 29

TO REPLACE MOTION DRIVE BELT (See Fig. 30)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

•Remove mower (See “TO REMOVE MOWER” in this section of this manual.)

•Disconnect clutch wire harness.

•Remove clutch locator.

•Remove belt from stationary idler and clutching idler.

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

•Pull belt toward front of tractor and remove downwards from around electric clutch.

•Install new belt by reversing above procedure.

ELECTRIC

CLUTCH LOCATOR

CLUTCH

 

CLUTCHING

IDLER

STATIONARY

IDLER

TRANSMISSION

INPUT PULLEYCLUTCH WIRE HARNESS

FIG. 30

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 31)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjust- ment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satisfied.

MOTION CONTROL

NEUTRAL

LEVER

LOCK

 

GATE

 

ADJUSTMENT BOLT

FIG. 31

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents DPR22H46STA Safe Operation Practices for Ride-On Mowers Safety RulesSafety Rules Table of Contents Unassembled Parts To Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorTo Attach Nose Roller See Fig Install Seat See FigTo Convert to Bagging or Discharging To SET UP Your Mower for Mulching See FigTo Install Mulcher Plate See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs Check Brake System Check Tire PressureCheck Mower Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Check Engine OIL Level Before Starting the EngineTo Operate on Hills Towing Carts and Other ATTACH- MentsPurge Transmission ADD GasolineTo Start Engine See Fig Mulching Mowing Tips Mowing TipsBefore Each USE Lubrication ChartCustomer Responsibilities General RecommendationsTractor Engine Engine OIL Filter CleaningMuffler Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig To Replace Mower Drive BeltTo Replace Motion Drive Belt See Fig To Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig Front Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigInterlocks and Relays Replacing Battery See FigTo Remove Hood and Grill Assembly See Fig To Replace Headlight BulbTo Adjust Carburetor To Adjust Throttle Control Cable See FigTo Adjust Choke Control See Fig Engine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsOFF Service Notes Tractor Model Number DPR22H46STA SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts Drive Repair Parts Steering Assembly KEY Part NO. NO.DESCRIPTION Optional Equipment EngineSeat Assembly Wheels & Tires DecalsMower Lift Mower Deck Repair Parts Limited Warranty Guide Only Ride UP and Down HillSighting Not Across HillParts and Service

DPR22H46STA specifications

The Poulan DPR22H46STA is a robust and versatile riding lawn mower designed for homeowners seeking efficiency and reliability in lawn maintenance. With its 22 horsepower engine and a 46-inch cutting deck, this lawn mower is ideal for tackling medium to large yards, making it a favorite among garden enthusiasts.

One of the primary features of the Poulan DPR22H46STA is its powerful engine. The 22 HP Briggs & Stratton engine provides ample power for cutting through thick grass and uneven terrain. It offers a smooth starting mechanism, ensuring that the mower is ready to go at a moment’s notice. This engine is also designed for efficiency, delivering a balance between power and fuel economy, which is vital for homeowners looking to reduce operational costs.

The 46-inch cutting deck is another standout feature of this model. This size enables the mower to cover a significant area with each pass, reducing overall mowing time. The deck is made from durable materials, ensuring it can withstand the rigors of frequent use while ensuring a clean and precise cut. Additionally, the cutting height can be easily adjusted, giving users the flexibility to customize their mowing experience based on grass length and weather conditions.

A key characteristic of the Poulan DPR22H46STA is its ease of maneuverability. The mower features a tight turning radius, allowing users to navigate around obstacles like trees, flower beds, and fences with minimal effort. The comfortable seat is designed ergonomically, providing ample support for long mowing sessions, and is adjustable to suit different user preferences.

For enhanced cutting efficiency, the mower utilizes a dual-blade system that distributes grass clippings evenly. This feature minimizes the need for bagging, as the finely chopped clippings can act as a natural fertilizer when left on the lawn. In addition, the mower’s compatibility with optional mulch kits provides even more versatility for grass care.

The Poulan DPR22H46STA also emphasizes user-friendly controls, with an intuitive dashboard that makes it easy to monitor speed, fuel level, and engine performance. This ensures that lawn care is not only effective but also enjoyable.

In summary, the Poulan DPR22H46STA combines power, efficiency, and ease of use, making it a fantastic choice for homeowners looking to maintain their lawns effortlessly. With its reliable engine, spacious cutting deck, and user-friendly design, this riding mower stands out as a valuable addition to any yard maintenance arsenal.
Top Page Image Contents