Poulan PO165H42A owner manual Tractor

Page 16

CUSTOMER RESPONSIBILITIES

TRACTOR

Always observe safety rules when performing any mainte- nance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 10)

•Raise mower to highest position to allow access to blades.

•Remove hex bolt, lock washer and flat washer securing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble hex bolt, lock washer and flat washer in exact order as shown.

•Tighten bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

TRAILING

MANDREL

EDGE UP

ASSEMBLY

 

BLADE

 

CENTER

 

HOLE

LOCK WASHER

 

 

STAR

 

FLAT WASHER

 

HEX BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE

IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 10

TO SHARPEN BLADE (See Fig. 11)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and even- tual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer).

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

CENTER HOLE

5/8" BOLT

BLADE

OR PIN

 

FIG. 11

BATTERY

Your tractor has a battery charging system which is suffi- cient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not

16necessary.

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model NO. PO165H42A Safety Rules Safe Operation Practices for Ride-On MowersTable of Contents Product Specifications Customer ResponsibilitiesUnassembled Parts Steering Wheel SeatKey Slope SheetAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig Lower seat into operating position and sit on seatCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips General Recommendations Customer ResponsibilitiesBefore Each USE Tractor Engine Muffler CleaningSpark Plugs Service and Adjustments To Level Mower HousingTo Install Mower See Fig To Remove Mower See FigTo Adjust Brake See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTransaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Carburetor To Replace Headlight BulbInterlocks and Relays To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PO165H42AElectrical KEY Part NO. NO.DESCRIPTION Chassis and Enclosures KEY Part Description Drive Repair Parts Steering Assembly KEY Part NO. NO.DESCRIPTION Engine KEY Part Description Seat Assembly Decals Wheels & TiresMower Lift Nut Lock w/Wsh 1/2-13 Unc Mower Deck Repair Parts Service Notes Service Notes Limited Warranty Sighting Guide CUT This OUT Dotted Is a Slope

PO165H42A specifications

The Poulan PO165H42A is a robust and reliable riding lawn mower designed for homeowners with medium to large yards. This machine is equipped to handle various lawn maintenance tasks, offering efficiency, comfort, and performance in one package.

One of the standout features of the PO165H42A is its powerful 16.5 HP Briggs & Stratton engine. This engine provides the necessary horsepower to tackle tougher terrains and thicker grass, ensuring a smooth cut every time. The mower's 42-inch cutting deck enables a wide cutting path, reducing the number of passes needed to achieve a well-manicured lawn. The deck also features six different cutting height adjustments, ranging from 1.5 inches to 4 inches, allowing users to customize their mowing experience based on their lawn's grass type and condition.

Another notable aspect is the pedal-operated automatic transmission, which provides ease of use. This feature allows for seamless speed adjustments while driving, ensuring that users can mow their lawns at their preferred pace without constantly shifting gears. The responsive steering system enhances maneuverability, enabling users to navigate around flower beds, trees, and other obstacles with ease.

Comfort is a priority with the Poulan PO165H42A, evident in its ergonomically designed high-back seat that provides support during extended mowing sessions. The easy-to-reach control panel and steering wheel ensure that all necessary functions are within easy access, reducing strain and enhancing the overall user experience.

In addition to its practical features, the PO165H42A also includes a 15-gallon rear-mounted grass catcher that helps keep lawns tidy by collecting clippings as you mow. This feature not only saves time but also eliminates the hassle of raking up cut grass afterward.

Poulan's commitment to durability is reflected in the rugged construction of the PO165H42A. The heavy-duty steel frame and reinforced cutting deck offer long-lasting performance, making it a worthy investment for homeowners looking to maintain their lawns efficiently. This riding mower is not only designed for power and performance but also built to withstand the rigors of regular lawn maintenance.

Overall, the Poulan PO165H42A is an excellent choice for homeowners seeking a reliable and user-friendly riding lawn mower that delivers powerful performance, comfort, and durability, ensuring a beautiful lawn year after year.
Top Page Image Contents