Poulan PO165H42A owner manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 23

SERVICE AND ADJUSTMENTS

KEPS NUT

 

HEX

 

BOLT

POSITIVE

 

(RED)

NEGATIVE

CABLE

(BLACK)

 

 

CABLE

FIG. 29

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 30)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

FIG. 30

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 31)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

•Check that holes “A” in governor control lever and hole in governor plate line-up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

GOVERNOR

 

GOVERNOR

CONTROL LEVER

CONTROL

 

 

 

 

PLATE

HOLES “A”

CLAMP

THROTTLE

 

SCREW

CABLE

FIG. 31

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjust- ment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR N E A R E S T A U T H O R I Z E D S E R V I C E C E N T E R / DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND E X P E R I E N C E T O M A K E A N Y N E C E S S A R Y ADJUSTMENTS.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model NO. PO165H42A Safe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Customer Responsibilities Product SpecificationsSlope Sheet Unassembled PartsSteering Wheel Seat KeyTo Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorLower seat into operating position and sit on seat Install Seat See FigCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Before Each USE Customer ResponsibilitiesGeneral Recommendations Tractor Engine Spark Plugs CleaningMuffler To Remove Mower See Fig Service and AdjustmentsTo Level Mower Housing To Install Mower See FigBelt Removal To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Remove Wheel for Repairs See FigTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number PO165H42A SchematicElectrical KEY Part NO. NO.DESCRIPTION Chassis and Enclosures KEY Part Description Drive Repair Parts Steering Assembly KEY Part NO. NO.DESCRIPTION Engine KEY Part Description Seat Assembly Wheels & Tires DecalsMower Lift Nut Lock w/Wsh 1/2-13 Unc Mower Deck Repair Parts Service Notes Service Notes Limited Warranty Slope Sighting Guide CUT This OUT Dotted Is a

PO165H42A specifications

The Poulan PO165H42A is a robust and reliable riding lawn mower designed for homeowners with medium to large yards. This machine is equipped to handle various lawn maintenance tasks, offering efficiency, comfort, and performance in one package.

One of the standout features of the PO165H42A is its powerful 16.5 HP Briggs & Stratton engine. This engine provides the necessary horsepower to tackle tougher terrains and thicker grass, ensuring a smooth cut every time. The mower's 42-inch cutting deck enables a wide cutting path, reducing the number of passes needed to achieve a well-manicured lawn. The deck also features six different cutting height adjustments, ranging from 1.5 inches to 4 inches, allowing users to customize their mowing experience based on their lawn's grass type and condition.

Another notable aspect is the pedal-operated automatic transmission, which provides ease of use. This feature allows for seamless speed adjustments while driving, ensuring that users can mow their lawns at their preferred pace without constantly shifting gears. The responsive steering system enhances maneuverability, enabling users to navigate around flower beds, trees, and other obstacles with ease.

Comfort is a priority with the Poulan PO165H42A, evident in its ergonomically designed high-back seat that provides support during extended mowing sessions. The easy-to-reach control panel and steering wheel ensure that all necessary functions are within easy access, reducing strain and enhancing the overall user experience.

In addition to its practical features, the PO165H42A also includes a 15-gallon rear-mounted grass catcher that helps keep lawns tidy by collecting clippings as you mow. This feature not only saves time but also eliminates the hassle of raking up cut grass afterward.

Poulan's commitment to durability is reflected in the rugged construction of the PO165H42A. The heavy-duty steel frame and reinforced cutting deck offer long-lasting performance, making it a worthy investment for homeowners looking to maintain their lawns efficiently. This riding mower is not only designed for power and performance but also built to withstand the rigors of regular lawn maintenance.

Overall, the Poulan PO165H42A is an excellent choice for homeowners seeking a reliable and user-friendly riding lawn mower that delivers powerful performance, comfort, and durability, ensuring a beautiful lawn year after year.
Top Page Image Contents