Poulan PO165H42A To Remove Wheel for Repairs See Fig, To Start Engine with a Weak Battery See Fig

Page 22

SERVICE AND ADJUSTMENTS

TO REMOVE WHEEL FOR REPAIRS (See Fig. 26)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 26

TO START ENGINE WITH A WEAK BATTERY (See Fig. 27)

CAUTION: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the CUSTOMER RESPON- SIBILITIES section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT NEGATIVE GROUNDED SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT NEGATIVE GROUNDED SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect each end of the RED cable to the POSITIVE (+) terminal of each battery, taking care not to short against chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal of fully charged battery.

•Connect the other end of the BLACK cable to good CHASSIS GROUND, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

POSITIVE TERMINAL

 

NEGATIVE TERMINAL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CHASSIS

 

 

CABLES

POSITIVE TERMINAL

CHARGED

BATTERY

 

 

NEGATIVE TERMINAL

FIG. 27

REPLACING BATTERY (See Figs. 28 and 29)

CAUTION: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

•Lift seat pan to raised position and open battery box door.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely.

•Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten securely.

•Close battery box door.

SEAT PAN

BATTERY

BOX DOOR

FIG. 28

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model NO. PO165H42A Safety Rules Safe Operation Practices for Ride-On MowersTable of Contents Product Specifications Customer ResponsibilitiesKey Unassembled PartsSteering Wheel Seat Slope SheetHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Lower seat into operating position and sit on seatCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips General Recommendations Customer ResponsibilitiesBefore Each USE Tractor Engine Muffler CleaningSpark Plugs To Install Mower See Fig Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig To Adjust Brake See FigBelt Installation Belt RemovalTo Adjust Steering Wheel Alignment Transaxle Motion Control Lever Neutral Adjustment See FigTransmission REMOVAL/REPLACEMENT To Replace Motion Drive Belt See FigTo Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Attach Jumper CablesInterlocks and Relays To Adjust CarburetorTo Replace Headlight Bulb To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PO165H42AElectrical KEY Part NO. NO.DESCRIPTION Chassis and Enclosures KEY Part Description Drive Repair Parts Steering Assembly KEY Part NO. NO.DESCRIPTION Engine KEY Part Description Seat Assembly Decals Wheels & TiresMower Lift Nut Lock w/Wsh 1/2-13 Unc Mower Deck Repair Parts Service Notes Service Notes Limited Warranty Sighting Guide CUT This OUT Dotted Is a Slope

PO165H42A specifications

The Poulan PO165H42A is a robust and reliable riding lawn mower designed for homeowners with medium to large yards. This machine is equipped to handle various lawn maintenance tasks, offering efficiency, comfort, and performance in one package.

One of the standout features of the PO165H42A is its powerful 16.5 HP Briggs & Stratton engine. This engine provides the necessary horsepower to tackle tougher terrains and thicker grass, ensuring a smooth cut every time. The mower's 42-inch cutting deck enables a wide cutting path, reducing the number of passes needed to achieve a well-manicured lawn. The deck also features six different cutting height adjustments, ranging from 1.5 inches to 4 inches, allowing users to customize their mowing experience based on their lawn's grass type and condition.

Another notable aspect is the pedal-operated automatic transmission, which provides ease of use. This feature allows for seamless speed adjustments while driving, ensuring that users can mow their lawns at their preferred pace without constantly shifting gears. The responsive steering system enhances maneuverability, enabling users to navigate around flower beds, trees, and other obstacles with ease.

Comfort is a priority with the Poulan PO165H42A, evident in its ergonomically designed high-back seat that provides support during extended mowing sessions. The easy-to-reach control panel and steering wheel ensure that all necessary functions are within easy access, reducing strain and enhancing the overall user experience.

In addition to its practical features, the PO165H42A also includes a 15-gallon rear-mounted grass catcher that helps keep lawns tidy by collecting clippings as you mow. This feature not only saves time but also eliminates the hassle of raking up cut grass afterward.

Poulan's commitment to durability is reflected in the rugged construction of the PO165H42A. The heavy-duty steel frame and reinforced cutting deck offer long-lasting performance, making it a worthy investment for homeowners looking to maintain their lawns efficiently. This riding mower is not only designed for power and performance but also built to withstand the rigors of regular lawn maintenance.

Overall, the Poulan PO165H42A is an excellent choice for homeowners seeking a reliable and user-friendly riding lawn mower that delivers powerful performance, comfort, and durability, ensuring a beautiful lawn year after year.
Top Page Image Contents