Poulan PO165H42A To Replace Mower Blade Drive Belt See Fig, To Adjust Brake See Fig, Belt Removal

Page 20

SERVICE AND ADJUSTMENTS

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

SUSPENSION ARM

LIFT LINK ADJUSTMENT NUT

FIG. 19

FRONT-TO-BACK ADJUSTMENT (See Figs. 20 and 21)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length. Both links should be approximately 10-3/8".

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

"D"

"D"

FIG. 20

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "E"

NUT "F"

TRUNNION

FRONT LINKS

FIG. 21

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 22)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instructions.

MANDREL PULLEY IDLER PULLEYS

MANDREL

PULLEY

FIG. 22

TO ADJUST BRAKE (See Fig. 23)

Your tractor is equipped with an adjustable brake system which is mounted on the side of the transaxle.

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted.

•Depress clutch/brake pedal and engage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Model NO. PO165H42A Safety Rules Safe Operation Practices for Ride-On MowersTable of Contents Product Specifications Customer ResponsibilitiesUnassembled Parts Steering Wheel SeatKey Slope SheetAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig Lower seat into operating position and sit on seatCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Before Each USE Customer ResponsibilitiesGeneral Recommendations Tractor Engine Spark Plugs CleaningMuffler Service and Adjustments To Level Mower HousingTo Install Mower See Fig To Remove Mower See FigTo Adjust Brake See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTransaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Carburetor To Replace Headlight BulbInterlocks and Relays To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PO165H42AElectrical KEY Part NO. NO.DESCRIPTION Chassis and Enclosures KEY Part Description Drive Repair Parts Steering Assembly KEY Part NO. NO.DESCRIPTION Engine KEY Part Description Seat Assembly Decals Wheels & TiresMower Lift Nut Lock w/Wsh 1/2-13 Unc Mower Deck Repair Parts Service Notes Service Notes Limited Warranty Sighting Guide CUT This OUT Dotted Is a Slope

PO165H42A specifications

The Poulan PO165H42A is a robust and reliable riding lawn mower designed for homeowners with medium to large yards. This machine is equipped to handle various lawn maintenance tasks, offering efficiency, comfort, and performance in one package.

One of the standout features of the PO165H42A is its powerful 16.5 HP Briggs & Stratton engine. This engine provides the necessary horsepower to tackle tougher terrains and thicker grass, ensuring a smooth cut every time. The mower's 42-inch cutting deck enables a wide cutting path, reducing the number of passes needed to achieve a well-manicured lawn. The deck also features six different cutting height adjustments, ranging from 1.5 inches to 4 inches, allowing users to customize their mowing experience based on their lawn's grass type and condition.

Another notable aspect is the pedal-operated automatic transmission, which provides ease of use. This feature allows for seamless speed adjustments while driving, ensuring that users can mow their lawns at their preferred pace without constantly shifting gears. The responsive steering system enhances maneuverability, enabling users to navigate around flower beds, trees, and other obstacles with ease.

Comfort is a priority with the Poulan PO165H42A, evident in its ergonomically designed high-back seat that provides support during extended mowing sessions. The easy-to-reach control panel and steering wheel ensure that all necessary functions are within easy access, reducing strain and enhancing the overall user experience.

In addition to its practical features, the PO165H42A also includes a 15-gallon rear-mounted grass catcher that helps keep lawns tidy by collecting clippings as you mow. This feature not only saves time but also eliminates the hassle of raking up cut grass afterward.

Poulan's commitment to durability is reflected in the rugged construction of the PO165H42A. The heavy-duty steel frame and reinforced cutting deck offer long-lasting performance, making it a worthy investment for homeowners looking to maintain their lawns efficiently. This riding mower is not only designed for power and performance but also built to withstand the rigors of regular lawn maintenance.

Overall, the Poulan PO165H42A is an excellent choice for homeowners seeking a reliable and user-friendly riding lawn mower that delivers powerful performance, comfort, and durability, ensuring a beautiful lawn year after year.
Top Page Image Contents