Poulan PR17H42STF owner manual Tractor

Page 16

CUSTOMER RESPONSIBILITIES

TRACTOR

Always observe safety rules when performing any mainte- nance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 12)

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and flat washer secur- ing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble blade bolt, lock washer and flat washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

TRAILING

MANDREL

ASSEMBLY

EDGE UP

 

BLADE

 

 

CENTER

 

HOLE

LOCK WASHER

STAR

FLAT WASHER

BLADE BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 12

TO SHARPEN BLADE (See Fig. 13)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and even- tual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer).

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

CENTER HOLE

5/8" BOLT

BLADE

OR PIN

 

FIG. 13

BATTERY

Your tractor has a battery charging system which is suffi- cient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents PR17H42STF Safety Rules IV. ServiceGeneral Operation II. Slope OperationSafety Rules Safe Operation Practices for Ride-On MowersTable of Contents Unassembled Parts Steering Wheel SeatSlope Sheet KeyAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CAR- TONInstall Seat See Fig To SET UP Your Mower for Mulching To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Adjust Mower Cutting Height See Fig Stopping See FigTo SET Parking Brake See Fig To USE Throttle Control See FigTo Adjust Gauge Wheels See Fig To Operate on HillsTo Operate Mower See Fig To Transport See FigsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsLubrication Chart Service DatesCustomer Responsibilities General RecommendationsTractor Engine Cleaning Engine Cooling FinsAIR Filter MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake See Fig Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Throttle Control Cable To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysStorage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PR17H42STF, Product Number 954 56Electrical KEY Part Description Chassis and Enclosures 158112 Keeper Belt Rear Lh Drive Repair Parts Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresEngine 170551 Control Th/ch Flag Mower Deck 179748 Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Page Page Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PR17H42STF specifications

The Poulan PR17H42STF is a robust and reliable riding lawn mower designed for homeowners seeking efficiency and ease of use in lawn maintenance. With a blend of powerful performance, innovative technologies, and user-friendly features, the PR17H42STF stands out as an excellent choice for tackling medium to large-sized lawns.

At the heart of the PR17H42STF is a potent 17.5 horsepower Briggs & Stratton engine. This powerful engine ensures smooth and consistent operation, enabling the mower to handle challenging terrain and thick grass with ease. The mower’s cutting deck measures 42 inches, allowing it to cover more ground in one pass, while still being compact enough to navigate narrow spaces and tight corners. The deck is constructed from high-quality materials designed for durability and long-lasting performance.

One of the key features of the PR17H42STF is its hydrostatic transmission. This technology provides an effortless driving experience, allowing the operator to easily adjust the speed without the need for manual gear shifting. This ease of operation makes mowing a more enjoyable task, especially for those new to riding mowers.

Additionally, the PR17H42STF offers a six-position height adjustment feature, giving the user complete control over the mowing height. Whether you prefer a manicured lawn or a taller grass finish, this mower adapts to your preferences seamlessly.

For enhanced comfort and convenience, the mower is equipped with an ergonomically designed seat and user-friendly controls positioned for easy access. The steering wheel is also designed to provide a comfortable grip, further reducing fatigue during extended mowing sessions.

The Poulan PR17H42STF includes a grass collection attachment option, making it easy to gather clippings and keep your yard tidy. Furthermore, its mulching capability allows for efficient nutrient recycling back into the soil, promoting a healthier lawn.

In conclusion, the Poulan PR17H42STF is an excellent investment for homeowners looking for a reliable and robust riding mower. Its combination of powerful performance, user-friendly features, and innovative technology makes it a standout choice for those serious about maintaining their outdoor spaces with minimal effort and maximum efficiency.
Top Page Image Contents