Poulan PR17H42STF To Adjust Gauge Wheels See Fig, To Operate on Hills, To Operate Mower See Fig

Page 12
3/8-16
LOCKNUT
GUAGE WHEEL MOUNTING BRACKET

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 7)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 3/8 washer, and 3/8-16 locknut and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

TO OPERATE ON HILLS

CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move motion control lever to neutral (N) position.

IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/BRAKE PEDAL IS DEPRESSED.

3/8 WASHER

SHOULDER

GAUGE WHEEL

BOLT

FIG. 7

TO OPERATE MOWER (See Fig. 8)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Lower mower with attachment lift control.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Slowly move motion control lever to slowest setting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 5 and 9)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attach- ment lift control.

•Pull freewheel control out and down into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

"ENGAGED" POSITION

 

ATTACHMENT

 

LIFT LEVER

 

HIGH POSITION

 

LOW

 

POSITION

ATTACHMENT

DEFLECTOR

CLUTCH LEVER

SHIELD

"DISENGAGED"

 

POSITION

 

FIG. 8

FIG. 9

TOWING CARTS AND OTHER ATTACHMENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PR17H42STF Safety Rules IV. ServiceGeneral Operation II. Slope OperationSafety Rules Safe Operation Practices for Ride-On MowersTable of Contents Unassembled Parts Steering Wheel SeatSlope Sheet KeyAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CAR- TONInstall Seat See Fig To SET UP Your Mower for Mulching To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Adjust Mower Cutting Height See Fig Stopping See FigTo SET Parking Brake See Fig To USE Throttle Control See FigTo Adjust Gauge Wheels See Fig To Operate on HillsTo Operate Mower See Fig To Transport See FigsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsLubrication Chart Service DatesCustomer Responsibilities General RecommendationsTractor Engine Cleaning Engine Cooling FinsAIR Filter MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake See Fig Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Throttle Control Cable To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysStorage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PR17H42STF, Product Number 954 56Electrical KEY Part Description Chassis and Enclosures 158112 Keeper Belt Rear Lh Drive Repair Parts Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresEngine 170551 Control Th/ch Flag Mower Deck 179748 Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Page Page Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PR17H42STF specifications

The Poulan PR17H42STF is a robust and reliable riding lawn mower designed for homeowners seeking efficiency and ease of use in lawn maintenance. With a blend of powerful performance, innovative technologies, and user-friendly features, the PR17H42STF stands out as an excellent choice for tackling medium to large-sized lawns.

At the heart of the PR17H42STF is a potent 17.5 horsepower Briggs & Stratton engine. This powerful engine ensures smooth and consistent operation, enabling the mower to handle challenging terrain and thick grass with ease. The mower’s cutting deck measures 42 inches, allowing it to cover more ground in one pass, while still being compact enough to navigate narrow spaces and tight corners. The deck is constructed from high-quality materials designed for durability and long-lasting performance.

One of the key features of the PR17H42STF is its hydrostatic transmission. This technology provides an effortless driving experience, allowing the operator to easily adjust the speed without the need for manual gear shifting. This ease of operation makes mowing a more enjoyable task, especially for those new to riding mowers.

Additionally, the PR17H42STF offers a six-position height adjustment feature, giving the user complete control over the mowing height. Whether you prefer a manicured lawn or a taller grass finish, this mower adapts to your preferences seamlessly.

For enhanced comfort and convenience, the mower is equipped with an ergonomically designed seat and user-friendly controls positioned for easy access. The steering wheel is also designed to provide a comfortable grip, further reducing fatigue during extended mowing sessions.

The Poulan PR17H42STF includes a grass collection attachment option, making it easy to gather clippings and keep your yard tidy. Furthermore, its mulching capability allows for efficient nutrient recycling back into the soil, promoting a healthier lawn.

In conclusion, the Poulan PR17H42STF is an excellent investment for homeowners looking for a reliable and robust riding mower. Its combination of powerful performance, user-friendly features, and innovative technology makes it a standout choice for those serious about maintaining their outdoor spaces with minimal effort and maximum efficiency.
Top Page Image Contents