Poulan PR17H42STF owner manual To Adjust Brake See Fig, To Replace Motion Drive Belt See Fig

Page 21

SERVICE AND ADJUSTMENTS

TO ADJUST BRAKE (See Fig. 23)

Your tractor is equipped with an adjustable brake system which is mounted on the side of the transaxle.

If tractor requires more than six (6) feet stopping distance at high speed in highest gear on a level dry concrete or paved surface, then brake must be adjusted.

•Depress clutch/brake pedal and engage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-9/16", loosen jam nut and turn nut “A” until distance becomes 1-9/16". Retighten jam nut against nut “A”.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than six (6) feet in highest gear, further maintenance is necessary. Contact your nearest au- thorized service center/department.

WITH PARKING BRAKE “ENGAGED”

 

NUT

 

1-9/16"

“A”

JAM NUT

 

OPERATING

ARM

DO NOT TOUCH THIS NUT. IF FURTHER BRAKE ADJUST- MENT IS NECESSARY CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTER/DEPARTMENT

FIG. 23

TO REPLACE MOTION DRIVE BELT (See Fig. 24)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Remove belt from stationary idler and clutching idler.

•Remove belt downward from around engine pulley.

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

•Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

•Carefully work new belt down around transmission cooling fan and onto the input pulley.

•Slide belt into the center span keeper.

•Pull belt toward front of tractor and roll around the top groove of engine pulley.

•Install belt through stationary idler and clutching idler.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this section of manual).

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

TRANSMISSION

INPUT PULLEY

FIG. 24

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See “PURGE TRANSMIS- SION” in the Operation section of this manual.

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT(See Fig. 25)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satisfied.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents PR17H42STF IV. Service Safety RulesGeneral Operation II. Slope OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Steering Wheel Seat Unassembled PartsSlope Sheet KeyTools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CAR- TONInstall Seat See Fig To Convert to Bagging or Discharging To SET UP Your Mower for MulchingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor To Adjust Mower Cutting Height See Fig Stopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control See FigTo Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMulching Mowing Tips Mowing TipsService Dates Lubrication ChartCustomer Responsibilities General RecommendationsTractor Engine Engine Cooling Fins CleaningAIR Filter MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalTransmission REMOVAL/REPLACEMENT To Adjust Brake See FigTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Carburetor To Adjust Throttle Control CableTo Replace Headlight Bulb Interlocks and RelaysOther StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number PR17H42STF, Product Number 954 56 SchematicElectrical KEY Part Description Chassis and Enclosures 158112 Keeper Belt Rear Lh Drive Repair Parts Steering Assembly KEY Part NO. NO. Description Seat Assembly Wheels and Tires DecalsEngine 170551 Control Th/ch Flag Mower Deck 179748 Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Page Page Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PR17H42STF specifications

The Poulan PR17H42STF is a robust and reliable riding lawn mower designed for homeowners seeking efficiency and ease of use in lawn maintenance. With a blend of powerful performance, innovative technologies, and user-friendly features, the PR17H42STF stands out as an excellent choice for tackling medium to large-sized lawns.

At the heart of the PR17H42STF is a potent 17.5 horsepower Briggs & Stratton engine. This powerful engine ensures smooth and consistent operation, enabling the mower to handle challenging terrain and thick grass with ease. The mower’s cutting deck measures 42 inches, allowing it to cover more ground in one pass, while still being compact enough to navigate narrow spaces and tight corners. The deck is constructed from high-quality materials designed for durability and long-lasting performance.

One of the key features of the PR17H42STF is its hydrostatic transmission. This technology provides an effortless driving experience, allowing the operator to easily adjust the speed without the need for manual gear shifting. This ease of operation makes mowing a more enjoyable task, especially for those new to riding mowers.

Additionally, the PR17H42STF offers a six-position height adjustment feature, giving the user complete control over the mowing height. Whether you prefer a manicured lawn or a taller grass finish, this mower adapts to your preferences seamlessly.

For enhanced comfort and convenience, the mower is equipped with an ergonomically designed seat and user-friendly controls positioned for easy access. The steering wheel is also designed to provide a comfortable grip, further reducing fatigue during extended mowing sessions.

The Poulan PR17H42STF includes a grass collection attachment option, making it easy to gather clippings and keep your yard tidy. Furthermore, its mulching capability allows for efficient nutrient recycling back into the soil, promoting a healthier lawn.

In conclusion, the Poulan PR17H42STF is an excellent investment for homeowners looking for a reliable and robust riding mower. Its combination of powerful performance, user-friendly features, and innovative technology makes it a standout choice for those serious about maintaining their outdoor spaces with minimal effort and maximum efficiency.
Top Page Image Contents