Poulan PP21H42 manual To Move Forward and Backward, To USE Cruise Control

Page 12

OPERATION

TO USE THROTTLE CONTROL (See Fig. 5)

Always operate engine at full speed (fast).

•Operating engine at less than full speed (fast) reduces engine's operating efficiency.

•Full speed (fast) offers the best mower performance.

TO MOVE FORWARD AND BACKWARD

The direction and speed of movement is controlled by the forward and reverse drive pedals.

•Start tractor and release parking brake.

•Slowly depress forward or reverse drive pedal to begin movement. Ground speed increases the further down the pedal is depressed.

TO USE CRUISE CONTROL

The cruise control feature can be used for forward travel only.

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrain or while trimming or turning.

•With forward drive pedal depressed to desired speed, move cruise control lever forward to “SET” position and hold while lifting your foot off the pedal, then release the cruise control lever.

•To disengage the cruise control, pull the lever backward to “OFF” position, or fully depress the brake pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 6)

The cutting height is controlled by turning the height ad- justment knob in desired direction.

•Turn knob clockwise ( ) to raise cutting height.

•Turn knob counterclockwise ( ) to lower cutting height.

The cutting height range is approximately 1-1/2" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 7)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Be sure tractor is on a flat level surface.

•Lower mower and adjust mower to desired cutting height(See “TO ADJUST MOWER CUTTING HEIGHT” in this section of manual).

•Remove retainer spring and clevis pin which secure each gauge wheel bar.

•Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

•Replace retainer spring into clevis pin.

•Be sure all gauge wheels are in the same setting.

IMPORTANT: BE SURE TO READJUST GAUGE WHEELS IF YOU CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.

RETAINER

SPRING

CLEVIS

PIN

FIG. 7

TO OPERATE MOWER (See Fig. 8)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut.

•Lower mower with attachment lift control.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

 

ATTACHMENT

 

LIFT LEVER

ATTACHMENT

HIGH POSITION

CLUTCH

 

ENGAGED

 

POSITION

LOW

 

 

POSITION

DISENGAGED

DEFLECTOR

POSITION"

SHIELD

 

FIG. 8

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PP21H42 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Steering WheelSeat Slope SheetAssembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidConnect Battery See Fig Assemble Gauge Wheels to Mower Deck See FigCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To SET Parking Brake See FigStopping See Fig To Move Forward and Backward To USE Cruise ControlService REMINDER/HOUR Meter Using the Reverse Operation SystemReverse Operation System ROS See Fig To Operate on HillsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Maintenance Lubrication ChartBattery TractorBlade Removal See Fig Engine Cleaning Service and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigLift Link Adjustment NUT To Replace Mower Blade Drive Belt See FigMandrel SuspensionTo Check and Adjust Brake See Fig To Replace Motion Drive Belt See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER To Replace Headlight BulbTo Remove Hood and Grill Assembly See Fig To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionWith attachment clutch Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXService Notes Service Notes

PP21H42 specifications

The Poulan PP21H42 is a powerful and versatile riding lawn mower that is designed to make your lawn care tasks easy and efficient. With its robust features and advanced technology, this mower is well-suited for both residential and small commercial use.

One of the standout characteristics of the Poulan PP21H42 is its 42-inch cutting deck. This size is ideal for maneuvering around obstacles such as trees and flower beds while still allowing for efficient cutting in larger areas. The cutting deck is made from high-quality steel, ensuring durability and longevity even in the toughest mowing conditions.

Powering the Poulan PP21H42 is a reliable Briggs & Stratton engine, known for its efficiency and performance. This engine delivers ample horsepower to tackle thick grass and uneven terrain. The included automatic transmission allows for smooth operation, enabling the operator to easily adjust speed without having to stop and shift gears manually.

The design of the Poulan PP21H42 enhances comfort and ease of use. Its ergonomic seat is adjustable, allowing users of different heights to find their ideal driving position. The mower is equipped with a tight turning radius, making it easier to navigate around obstacles, and the easy-to-access control panel ensures that operators have everything they need at their fingertips.

One of the key technologies featured in the Poulan PP21H42 is its cutting height adjustment feature. With a simple lever, users can adjust the cutting height to one of six different positions, ranging from 1 to 4 inches, allowing for customized cutting according to different lawn types and conditions.

Additionally, this mower comes with a mulching kit option, which finely chops grass clippings and redistributes them back onto the lawn, returning nutrients to the soil and promoting healthier grass growth. The side discharge chute design efficiently disperses clippings without clogging, ensuring a clean and neat finish after mowing.

Safety features are also a priority in the Poulan PP21H42. The mower is equipped with a safety switch that engages when the operator leaves the seat, preventing accidental starts or injuries.

Overall, the Poulan PP21H42 combines performance, comfort, and safety, making it an excellent choice for anyone looking to maintain a well-kept lawn with minimal effort. Whether you have a large yard or a small property, the PP21H42 provides the tools and technology needed for effective lawn care.
Top Page Image Contents