Poulan PP21H42 manual To Replace Mower Blade Drive Belt See Fig, Mandrel, Suspension, Arm

Page 21

SERVICE AND ADJUSTMENTS

SIDE-TO-SIDE ADJUSTMENT (See Fig. 17)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

00598

OF MOWER TO

GROUND

GROUND

 

A

GROUND LINE

A

 

 

FIG. 17

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

FRONT-TO-BACK ADJUSTMENT (See Figs. 18 - 20)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

01268

MANDREL

“D” “D”

FIG. 18

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

SUSPENSION

ARM

01553

LIFT LINK ADJUSTMENT NUT

FIG. 19

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

01267

NUT “E”

NUT “F”

TRUNNION

01156

FRONT LINKS

FIG. 20

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 21)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

IDLER PULLEYS

MANDREL

PULLEYS

0 2314

FIG. 21

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents PP21H42 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Steering Wheel Unassembled PartsSeat Slope SheetTools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidAssemble Gauge Wheels to Mower Deck See Fig Connect Battery See FigCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To SET Parking Brake See FigStopping See Fig To USE Cruise Control To Move Forward and BackwardUsing the Reverse Operation System Service REMINDER/HOUR MeterReverse Operation System ROS See Fig To Operate on HillsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMowing Tips Lubrication Chart MaintenanceBattery TractorBlade Removal See Fig Engine Cleaning To Install Mower See Fig Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig Lift Link Adjustment NUTMandrel SuspensionTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN/CAMBER To Replace Headlight BulbTo Adjust Throttle Control Cable To Remove Hood and Grill Assembly See FigTo Adjust Choke Control To Adjust CarburetorOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsWith attachment clutch Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationService Notes Service Notes

PP21H42 specifications

The Poulan PP21H42 is a powerful and versatile riding lawn mower that is designed to make your lawn care tasks easy and efficient. With its robust features and advanced technology, this mower is well-suited for both residential and small commercial use.

One of the standout characteristics of the Poulan PP21H42 is its 42-inch cutting deck. This size is ideal for maneuvering around obstacles such as trees and flower beds while still allowing for efficient cutting in larger areas. The cutting deck is made from high-quality steel, ensuring durability and longevity even in the toughest mowing conditions.

Powering the Poulan PP21H42 is a reliable Briggs & Stratton engine, known for its efficiency and performance. This engine delivers ample horsepower to tackle thick grass and uneven terrain. The included automatic transmission allows for smooth operation, enabling the operator to easily adjust speed without having to stop and shift gears manually.

The design of the Poulan PP21H42 enhances comfort and ease of use. Its ergonomic seat is adjustable, allowing users of different heights to find their ideal driving position. The mower is equipped with a tight turning radius, making it easier to navigate around obstacles, and the easy-to-access control panel ensures that operators have everything they need at their fingertips.

One of the key technologies featured in the Poulan PP21H42 is its cutting height adjustment feature. With a simple lever, users can adjust the cutting height to one of six different positions, ranging from 1 to 4 inches, allowing for customized cutting according to different lawn types and conditions.

Additionally, this mower comes with a mulching kit option, which finely chops grass clippings and redistributes them back onto the lawn, returning nutrients to the soil and promoting healthier grass growth. The side discharge chute design efficiently disperses clippings without clogging, ensuring a clean and neat finish after mowing.

Safety features are also a priority in the Poulan PP21H42. The mower is equipped with a safety switch that engages when the operator leaves the seat, preventing accidental starts or injuries.

Overall, the Poulan PP21H42 combines performance, comfort, and safety, making it an excellent choice for anyone looking to maintain a well-kept lawn with minimal effort. Whether you have a large yard or a small property, the PP21H42 provides the tools and technology needed for effective lawn care.
Top Page Image Contents