Poulan PP21H42 Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

3/4" wrench

Pliers

(2)

7/16" wrenches

Tire pressure gauge

 

 

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dashed lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

5/16 HEX BOLT

5/16 LOCK WASHER

LARGE FLAT WASHER

STEERING

WHEEL

STEERING BOOT

ADAPTER

EXTENSION SHAFT

LOWER

STEERING

SHAFT

FIG. 1

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PP21H42 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Seat Unassembled PartsSteering Wheel Slope SheetTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidConnect Battery See Fig Assemble Gauge Wheels to Mower Deck See FigCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To SET Parking Brake See FigStopping See Fig To Move Forward and Backward To USE Cruise ControlReverse Operation System ROS See Fig Service REMINDER/HOUR MeterUsing the Reverse Operation System To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Maintenance Lubrication ChartBattery TractorBlade Removal See Fig Engine Cleaning To Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigMandrel Lift Link Adjustment NUTTo Replace Mower Blade Drive Belt See Fig SuspensionTo Check and Adjust Brake See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment To Replace Headlight BulbTo Adjust Choke Control To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable To Adjust CarburetorFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionWith attachment clutch Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXService Notes Service Notes

PP21H42 specifications

The Poulan PP21H42 is a powerful and versatile riding lawn mower that is designed to make your lawn care tasks easy and efficient. With its robust features and advanced technology, this mower is well-suited for both residential and small commercial use.

One of the standout characteristics of the Poulan PP21H42 is its 42-inch cutting deck. This size is ideal for maneuvering around obstacles such as trees and flower beds while still allowing for efficient cutting in larger areas. The cutting deck is made from high-quality steel, ensuring durability and longevity even in the toughest mowing conditions.

Powering the Poulan PP21H42 is a reliable Briggs & Stratton engine, known for its efficiency and performance. This engine delivers ample horsepower to tackle thick grass and uneven terrain. The included automatic transmission allows for smooth operation, enabling the operator to easily adjust speed without having to stop and shift gears manually.

The design of the Poulan PP21H42 enhances comfort and ease of use. Its ergonomic seat is adjustable, allowing users of different heights to find their ideal driving position. The mower is equipped with a tight turning radius, making it easier to navigate around obstacles, and the easy-to-access control panel ensures that operators have everything they need at their fingertips.

One of the key technologies featured in the Poulan PP21H42 is its cutting height adjustment feature. With a simple lever, users can adjust the cutting height to one of six different positions, ranging from 1 to 4 inches, allowing for customized cutting according to different lawn types and conditions.

Additionally, this mower comes with a mulching kit option, which finely chops grass clippings and redistributes them back onto the lawn, returning nutrients to the soil and promoting healthier grass growth. The side discharge chute design efficiently disperses clippings without clogging, ensuring a clean and neat finish after mowing.

Safety features are also a priority in the Poulan PP21H42. The mower is equipped with a safety switch that engages when the operator leaves the seat, preventing accidental starts or injuries.

Overall, the Poulan PP21H42 combines performance, comfort, and safety, making it an excellent choice for anyone looking to maintain a well-kept lawn with minimal effort. Whether you have a large yard or a small property, the PP21H42 provides the tools and technology needed for effective lawn care.
Top Page Image Contents