Poulan PPH20K46 manual Front Wheel TOE-IN/CAMBER, To Remove Wheel for Repairs See Fig

Page 22

SERVICE AND ADJUSTMENTS

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 31)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

Fig. 31

TO START ENGINE WITH A WEAK BATTERY (See Fig. 32)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WEAK OR DEAD

 

 

 

 

 

 

 

FULLY CHARGED

BATTERY

 

 

 

 

 

 

 

BATTERY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. 32

REPLACING BATTERY (See Fig. 33)

WARNING: Do not short battery ter- minals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from acci- dental grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

DISCARD TERMINAL

KEPS NUT

HEX BOLT

 

PROTECTIVE CAPS

 

 

 

TERMINAL

 

 

COVER

 

 

 

 

NEGATIVE

POSITIVE (RED)

 

(BLACK)

 

CABLE

CABLE

 

 

 

 

03037

 

22

Fig. 33

 

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PPH20K46 ModelGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyTools Required for Assembly To Remove Tractor from CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor H ETo USE Throttle Control D See Fig HOW to USE Your TractorTo SET Parking Brake See Fig Stopping See FigTo USE Cruise Control J See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Before Starting the EngineReverse Operation System ROS To Transport See FigsTo Start Engine See Fig Service REMINDER/HOUR MeterADD Gasoline Automatic Transmission Warm UPPurge Transmission Mowing TipsRunning Maintenance Lubrication ChartBlade Care BatteryTractor Blade Removal See FigEngine Muffler CleaningEngine OIL Filter Spark PlugsTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower Turn nut right Turn nut left To raise mower To lower mowerTo Replace Motion Drive Belt See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check BrakeFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove Wheel for Repairs See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Suggested Guide for Sighting Slopes for Safe Operation Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Degrés Dépannage DE Guide Correction Cause ProblèmeLame de mandrin le Remplacez Tordu est lame de mandrin Un Moteur EntreposageTracteur Reglages ET Revision Starter DU Commande LA Régler PourGAZ DES Commande LA DE Câble LE Régler Pour Carburateur LE Régler PourAvant Fig la Voir Batterie LA ReplacerFig la Voir Tionsrapa RÉ LES Pour Roues LES Enlever PourFig la Voir Réglages ET RévisionFig la Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl Pour Courroie Acer Rempl Pour27 .Fig Tondeuse LA Niveau LE Ajuster Pour28 .Fig 26 .Fig21 .Fig 24 .Fig23 .Fig 20 .Fig19 .Fig Fig VoirTondeuse LA Enlever Pour Réglages OU SionsFig La Voir Coupe DE Plateau DU Lavage DE Raccord Entretien’ALLUMAGE Bougie ’AIR Tamis LE Nettoyer Moteur DE D’HUILE FiltreAIR À Filtre Sionmistrans LA DE Moteur FluidePneus Fig la Voir Lame LA EnleverLames DES Entretien Frein DU FonctionnementLubrification DE Tableau Recommandations LESGénérales Utilisation Chaque AvantTransmission LA Purger UtilisationTondre DE Conseils 12 .Fig’ENTRETIEN/HOROMÈTRE Indicateur Moteur LE Démarrer Pour’ESSENCE Réservoir LE Remplir Quetimaauto11 et 3 .Fig les Voir Moteur LE Démarrer DE AvantMAR EN Fonctionnement DE Système Tondeuse LA Utiliser Pour Fig la Voir J Vitesse DE Régulateur LE Utiliser CommentTondeuse DE Lames LES Arrêter Pour Jauge DE Roues LES Régler PourReculer Pour ET Avancer Pour GAZ DES Commande LA Utiliser PourFig la Voir Mentnetionsta DE Frein LE Engager Pour MoteurUtilisation ’EMBRAYAGE Desmancom des fonction la et MontageTionsec la Voir Rouler Faisant LE EN TE LE Pour Exigés Outils LES Montées NON PiécesTracteur Votre DE Getamon Fig la Voir Batterie LA VérifierClient DU Responsabilités SommaireProduit DE Spécifications Enfants EntretienRemorquage Général EntretienGénéral Fonctionnement PentesLES Dans Fonctionnement Tracteurs des sécurité toute en l’utilisation pour ConseilsAvertissement

PPH20K46 specifications

The Poulan PPH20K46 is a robust and versatile riding lawn mower designed for homeowners with larger gardens or properties that require efficient mowing. This powerful machine features an ergonomic design and advanced technologies that make lawn care simpler and more enjoyable.

At the heart of the Poulan PPH20K46 is its 46-inch cutting deck, which allows for a wide cutting path, reducing the number of passes needed to complete the mowing task. This feature is ideal for covering large areas quickly while maintaining an even and precise cut. The cutting height can be easily adjusted, providing versatility in lawn care. Users can select from different cutting heights, ensuring optimal results whether the grass is tall or short.

Powered by a reliable 20 horsepower Briggs & Stratton engine, the PPH20K46 delivers ample power to tackle dense grass and tough terrain. The engine is designed for durability and efficiency, ensuring that you spend less time on maintenance and more time enjoying your beautifully manicured lawn. Additionally, the electric start feature adds convenience, allowing users to start the mower with the simple push of a button.

One of the standout characteristics of the Poulan PPH20K46 is its hydrostatic transmission. This technology allows for smooth and seamless operation without the need for shifting gears. Users can easily adjust their speed on the fly, making maneuvering around obstacles or tight corners a breeze. The fully adjustable seat and steering wheel offer customizable comfort, enabling users to find the perfect position for optimal control and visibility.

For those who value cleanliness in lawn care, the mower is equipped with a washout port on the deck. This allows for easy cleaning after mowing, ensuring that grass clippings do not accumulate and impact the performance of the cutting deck.

In terms of aesthetics, the PPH20K46 offers a sleek design that is both functional and appealing. The bright yellow color is not only distinctive but also enhances visibility, ensuring that the mower is easily seen while in use.

Overall, the Poulan PPH20K46 combines power, efficiency, and comfort, making it an excellent choice for homeowners looking to maintain their lawns effortlessly. With its array of features and technology, it stands out as a reliable companion for any lawn care regimen. Whether you are tackling large swaths of grass or navigating intricate landscaping, the PPH20K46 is engineered to meet the demands of modern mowing.
Top Page Image Contents