Poulan PPH23B48 manual To Replace Mower Blade Drive Belt See Fig, To Check Brake

Page 22

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 33)

MOWER DRIVE BELT REMOVAL

•Park tractor on a level surface. Engage parking brake.

•Lower attachment lift lever to its lowest position.

•Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.

•Remove belt from electric clutch pulley (M), both man- drel pulleys (R) and all idler pulleys (V).

MOWER DRIVE BELT INSTALLATION

•Install belt around all mandrel pulleys (R) and around idler pulleys (V) as shown.

•Install belt onto electric clutch pulley (M).

IMPORTANT: Check belt for proper routing in all mower pulley grooves.

•Raise attachment lift lever to highest position.

V

M

R

R

Fig. 33

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

1.Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

2.Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, then the brakeneedstobeserviced.Contactaqualifiedservicecenter.

TO REPLACE MOTION DRIVE BELT (See Fig. 34)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

1.Remove mower (See “TO REMOVE MOWER” section in this manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

2.Disconnect clutch wire harness (A).

3.Remove anti-rotation link (B) on right side of tractor.

4.Remove belt from stationary idler (C) and clutching idler (D).

5.Remove belt from centerspan idler (E).

6.Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades (F).

7.Remove belt downward from engine pulley and around electric clutch (G).

8- Slide belt toward rear of tractor, off the steering plate

(H)and remove from tractor.

BELT INSTALLATION -

1.Install new belt from tractor rear to front, over the steer- ing plate (H) and above clutch brake pedal shaft (J).

2.Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley (G).

3.Pull belt toward rear of tractor. Carefully work belt down around transmission cooling fan and onto the input pulley (F). Be sure belt is inside the belt keeper.

4.Install belt on centerspan idler (E).

5.Install belt through stationary idler (C) and clutching idler (D).

6.Reinstall anti-rotation link (B) on right side of tractor. Tighten securely.

7.Reconnect clutch harness (A).

8- Make sure belt is in all pulley grooves and inside all belt guides and keepers.

9.Install mower (See “TO INSTALL MOWER” section in this manual).

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PPH23B48 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyTools Required for Assembly To Remove Tractor from CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor To SET Parking Brake See Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged Stopping See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigReverse Operation System ROS Service REMINDER/HOUR MeterTo Operate Mower To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionLubrication Chart MaintenancePowdered Graphite Type Lubricant Sparingly Blade Care BatteryTractor Blade Removal See FigEngine Cleaning To Install Mower See Figs Service and AdjustmentsTo Remove Mower See Fig First Install ANTI-SWAY BAR S M F Engage belt tension rod K on locking bracket LTo Level Mower Visual SIDE-TO-SIDE Adjustment See FigPrecision SIDE-TO-SIDE Adjustment See Fig Turn nut right Turn nut left To raise mowerTo Check Brake To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig To Remove Wheel for Repairs See FigTransmission Fuel System StorageOther Engine OILTroubleshooting Problem Cause CorrectionFires when turn To run when operBattery will not Engine continuesService Notes Suggested Guide for Sighting Slopes for Safe Operation Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Degrés MAX ’ENTRETIEN Remarques Dépannage DE Guide Correction Cause ProblèmePuissance de Entreposage Moteur Starter DU Commande LA Régler PourReglages ET Revision Carburateur LE Régler PourLA DE L’ALIGNEMENT Régler Pour RossageAVANT/CAR Roues DES Convergence Fig la Voir Faible RietebatFig la Voir Tondeuse LA DE Lame Fig la Voir D’ENTRAÎNEMENTCourroie Acer Rempl Pour Freins LES Vérifier Pour LA DE Courroie LA Remplacer Pour31 .Fig Tondeuse LA Niveau LE Ajuster Pour32 .Fig 30 .Fig27 .Fig Avant l’embrayage de poulie la sur courroie la Installez28 .Fig 26 .Fig23 .FIG 25 .FIG24 .FIG 22 .FIG18 19 .Fig 20 .Fig Tondeuse LA Installer28 19 .Figs les Voir Stationnement de frein le actionnez et niveauEntretien Lubrification Sionmistrans LA DE Moteur FluideFig La Voir Coupe DE Plateau DU Lavage DE Raccord Transmission LA DE EntretienPneus Fig la Voir Lame LA EnleverLames DES Entretien Frein DU FonctionnementUtilisation Chaque Avant Lubrification DE TableauTransmission LA Purger Avant ET Réinstallation LA Après Purgée ÊtreUtilisation 13 .Fig’ESSENCE Réservoir LE Remplir Moteur DU D’HUILE Niveau LE VérifierTracteur LE Transporter Pour Accessoires Autres ET Charrettes DES Remorquer PourROS Arrière Marche EN Fonctionnement DE Système Pentes LES Dans Utiliser PourFig la Voir J Vitesse DE Régulateur LE Utiliser Comment Tondeuse DE Lames LES Arrêter PourJauge DE Roues LES Régler Pour Tondeuse LA Utiliser PourFig la Voir Mentnetionsta DE Frein LE Embrayée Pour GAZ DES Commande LA Utiliser PourFig la Voir Arrêter Pour Moteur’ACCESSOIRE D’EMBRAYAGE Interrupteur E Propriété la de lendommagement et/ou sérieuses Montage NI DE EST Tondeuse LA SI VérifierMontées NON Piéces DU Tracteur LE Sortir PourClient DU Responsabilités UtilisationMontage Produit DE SpécificationsRemorquage EnfantsEntretien Général EntretienTracteurs des sécurité toute en l’utilisation pour Conseils AvertissementPentes LES Dans Fonctionnement Général FonctionnementU the in Printed SR 09.06.02 Avertissement

PPH23B48 specifications

The Poulan PPH23B48 is a versatile and powerful lawn tractor designed for homeowners who demand efficiency and comfort in their outdoor mowing tasks. Engineered to handle a variety of yard sizes, this model boasts a reliable Briggs & Stratton engine that delivers robust performance for tackling grass and terrain with ease.

One of the standout features of the PPH23B48 is its 48-inch cutting deck. This wide cutting path allows for quicker mowing sessions, enabling users to cover more ground in less time. The deck is crafted from durable materials to withstand the rigors of frequent use while providing clean and even cuts. The adjustable cutting height feature offers six positions, allowing operators to customize grass length to suit their preferences and environmental conditions.

The Poulan PPH23B48 is equipped with an innovative hydrostatic transmission system, which contributes to a smoother driving experience. This technology eliminates the need for manual shifting, allowing riders to easily control their speed without the hassle of changing gears. This feature is especially beneficial for navigating various terrains, as it enables seamless transitions from flat lawns to inclines.

Comfort is paramount in the design of the PPH23B48. The ergonomic seat is designed for prolong use, reducing fatigue during longer mowing sessions. With a user-friendly dashboard, operators can quickly monitor fuel levels, engine performance, and operational settings, ensuring efficient management of mowing tasks.

Furthermore, Poulan has incorporated a tight turning radius into this model, which enhances maneuverability around obstacles like trees and flower beds. The easy-to-use steering wheel provides precision control, making it simple for users to navigate their yards effortlessly.

The PPH23B48 is also equipped with a mulching capability, which allows users to recycle grass clippings back into the lawn. This eco-friendly feature not only reduces waste but also adds valuable nutrients back into the soil, promoting a healthier lawn.

In summary, the Poulan PPH23B48 combines power, efficiency, and user-centric design to create a lawn tractor that meets the needs of various homeowners. Its thoughtful features and advanced technologies make outdoor mowing not just a chore, but a manageable and enjoyable task.
Top Page Image Contents