Poulan PPR20H42STB To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 12

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 7)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 3/8 washer, and 3/8-16 locknut and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

3/8-16

LOCKNUT

GUAGE WHEEL

MOUNTING

BRACKET

3/8 WASHER

SHOULDER

GAUGE WHEEL

BOLT

 

FIG. 7

TO OPERATE MOWER (See Fig. 8)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

"ENGAGED" POSITION

ATTACHMENT LIFT LEVER HIGH POSITION

ATTACHMENT

 

CLUTCH LEVER

LOW

"DISENGAGED"

POSITION

POSITION

 

DEFLECTOR

SHIELD

FIG. 8

TO OPERATE ON HILLS

CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move motion control lever to neutral (N) position.

IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/BRAKE PEDAL IS DEPRESSED.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Slowly move motion control lever to slowest setting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 5 and 9)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attach- ment lift control.

•Pull freewheel control out and down into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PPR20H42STB Safety Rules IV. ServiceGeneral Operation II. Slope OperationSafety Rules Table of Contents Unassembled Parts Steering Wheel SeatSlope Sheet Assembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To SET UP Your Mower for Mulching Check Tire PressureCheck Deck Levelness To Convert to Bagging or DischargingOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Towing Carts and Other AttachMents Check Engine OIL LevelMowing Tips Purge TransmissionAutomatic Transmission Warm UP Mulching Mowing Tips Lubrication Chart Everybefore Service DatesCustomer Responsibilities General RecommendationsTractor Brake OperationTires Operator Presence SystemEngine Clean AIR Screen Clean AIR INTAKE/COOLING AreasCleaning MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Adjust Brake See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTransmission REMOVAL/REPLACEMENT Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsTo Replace Headlight Bulb To Attach Jumper CablesTo Adjust Carburetor Interlocks and RelaysTo Replace Fuse Storage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PPR20H42STBElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive KEY Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresEngine Optional EquipmentSpark Arrester 170771 Control, Throttle Mower Deck Wheel, Gauge Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PPR20H42STB specifications

The Poulan PPR20H42STB is a versatile and efficient riding mower that stands out for its performance and user-friendly features. Tailored for residential use, it is perfect for homeowners with medium to large lawns, combining power, durability, and ease of maintenance. This mower is designed to tackle a variety of terrain types, making it a reliable choice for lawn care enthusiasts.

One of the main features of the PPR20H42STB is its robust 20 horsepower Briggs & Stratton engine, which provides ample power to drive the mower efficiently across various landscapes. This engine is designed for reliability and optimal performance, ensuring that users can complete their mowing tasks with ease. The mower is equipped with a hydrostatic transmission, which facilitates smooth and precise speed adjustments without the need for manual gear changes. This feature enhances the overall driving experience, allowing operators to focus on getting the job done.

The cutting deck of the PPR20H42STB measures 42 inches, making it ideal for maneuvering around obstacles while still covering substantial ground in each pass. This size strikes a balance between efficiency and agility, allowing for effective mowing in tighter spaces such as gardens or around trees. The deck is adjustable, enabling users to select the desired cutting height between 1.5 inches and 4 inches. This versatility caters to different grass types and conditions, ensuring an even and pristine cut.

Another notable characteristic of the Poulan PPR20H42STB is its ergonomic design. The comfortable operator's seat and control layout enhance the user experience during extended mowing sessions. The steering wheel is positioned for easy access to controls, and the foot pedal allows for simple operation of the hydrostatic transmission, contributing to a more pleasant mowing experience.

Moreover, the PPR20H42STB features a spacious fuel tank that accommodates more fuel, reducing the frequency of refueling during larger mowing tasks. Its durable construction ensures longevity and reliability, making it a valuable investment for homeowners seeking an efficient lawn care solution.

In summary, the Poulan PPR20H42STB combines powerful performance, user-friendly features, and versatile mowing capabilities. It is an excellent choice for homeowners looking for a reliable riding mower to keep their lawns looking immaculate.
Top Page Image Contents