Poulan PPR20H42STB owner manual Tools Required for Assembly, To Remove Tractor from Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

Utility knife

Pliers

(1)

3/4" wrenches

Tire pressure gauge

(2)

7/16" wrenches

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

Remove all accessible loose parts and parts cartons from carton.

Cut, from top to bottom, along lines on all four corners of carton, and lay panels flat.

Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

Slide extension shaft onto lower steering shaft. Align mount- ing holes in extension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 10-12 FT. LBS TORQUE.

Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

Position front wheels of the tractor so they are pointing

 

straight forward.

Remove steering wheel adapter from steering wheel and

 

slide adapter onto steering shaft extension.

STEERING WHEEL

ADAPTER

1/4 LOCKNUT

LOWER

STEERING

SHAFT

INSERT

1/2 HEX NUT

LARGE FLAT

WASHER

STEERING

BOOT

TABS

EXTENSION SHAFT

1/4 HEX BOLT

TAB

SLOTS

• Position steering wheel so cross bars are horizontal (left to

 

right) and slide inside boot and onto adapter.

• Assemble large flat washer, 1/2 hex nut and tighten securely.

Snap steering wheel insert into center of steering wheel.

Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

FIG. 1

HOW TO SET UP YOUR TRACTOR

CHECK BATTERY (See Fig. 2)

Lift seat pan to raised position.

If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in CUSTOMER RESPONSIBILITIES section of this manual for charging instructions).

6

Image 6
Contents PPR20H42STB General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Table of Contents Unassembled Parts Steering Wheel SeatSlope Sheet HOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Check Deck Levelness To SET UP Your Mower for MulchingCheck Tire Pressure To Convert to Bagging or DischargingOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsMents Before Starting the EngineTowing Carts and Other Attach Check Engine OIL LevelMowing Tips Purge TransmissionAutomatic Transmission Warm UP Mulching Mowing Tips Customer Responsibilities Lubrication ChartEverybefore Service Dates General RecommendationsTires TractorBrake Operation Operator Presence SystemEngine Cleaning Clean AIR ScreenClean AIR INTAKE/COOLING Areas MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Blade Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral Adjustment See Fig Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Attach Jumper CablesTo Adjust Carburetor Interlocks and RelaysTo Replace Fuse Fuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PPR20H42STBElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive KEY Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresEngine Optional EquipmentSpark Arrester 170771 Control, Throttle Mower Deck Wheel, Gauge Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PPR20H42STB specifications

The Poulan PPR20H42STB is a versatile and efficient riding mower that stands out for its performance and user-friendly features. Tailored for residential use, it is perfect for homeowners with medium to large lawns, combining power, durability, and ease of maintenance. This mower is designed to tackle a variety of terrain types, making it a reliable choice for lawn care enthusiasts.

One of the main features of the PPR20H42STB is its robust 20 horsepower Briggs & Stratton engine, which provides ample power to drive the mower efficiently across various landscapes. This engine is designed for reliability and optimal performance, ensuring that users can complete their mowing tasks with ease. The mower is equipped with a hydrostatic transmission, which facilitates smooth and precise speed adjustments without the need for manual gear changes. This feature enhances the overall driving experience, allowing operators to focus on getting the job done.

The cutting deck of the PPR20H42STB measures 42 inches, making it ideal for maneuvering around obstacles while still covering substantial ground in each pass. This size strikes a balance between efficiency and agility, allowing for effective mowing in tighter spaces such as gardens or around trees. The deck is adjustable, enabling users to select the desired cutting height between 1.5 inches and 4 inches. This versatility caters to different grass types and conditions, ensuring an even and pristine cut.

Another notable characteristic of the Poulan PPR20H42STB is its ergonomic design. The comfortable operator's seat and control layout enhance the user experience during extended mowing sessions. The steering wheel is positioned for easy access to controls, and the foot pedal allows for simple operation of the hydrostatic transmission, contributing to a more pleasant mowing experience.

Moreover, the PPR20H42STB features a spacious fuel tank that accommodates more fuel, reducing the frequency of refueling during larger mowing tasks. Its durable construction ensures longevity and reliability, making it a valuable investment for homeowners seeking an efficient lawn care solution.

In summary, the Poulan PPR20H42STB combines powerful performance, user-friendly features, and versatile mowing capabilities. It is an excellent choice for homeowners looking for a reliable riding mower to keep their lawns looking immaculate.