Poulan PPR20H42STB owner manual Install Seat See Fig

Page 7

ASSEMBLY

SEAT PAN

LABLE

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Operation section, page 10, for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place freewheel control in freewheeling position to disengage transmission (See “TO TRANSPORT” in the Operation section of this manual).

FIG. 2

INSTALL SEAT (See Fig. 3)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Roll tractor forward off skid.

•Remove banding holding deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Opera- tion section, page 10, for location and func- tion of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been completed.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in "transmission engaged" po- sition.

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

• Get off seat without moving its adjusted position.

•

Place motion control lever in neutral (N) position.

• Raise seat and tighten adjustment knob securely.

•

Press lift lever plunger and raise attachment lift lever to

 

 

its highest position.

 

• Start the engine. After engine has started, move throttle

SEAT

 

control to idle position.

•

Release parking brake.

 

 

• Slowly move the motion control lever forward and slowly

 

 

drive tractor off skid.

 

• Apply brake to stop tractor, set parking brake and place

SEAT PAN

 

motion control lever in neutral position.

• Turn ignition key to "OFF" position.

 

 

Continue with the instructions that follow.

SHOULDER

 

 

BOLT

 

 

FLAT WASHER

 

 

ADJUSTMENT

 

 

KNOB

 

 

FIG. 3

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents PPR20H42STB II. Slope Operation Safety RulesIV. Service General OperationSafety Rules Table of Contents Steering Wheel Seat Unassembled PartsSlope Sheet To Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorInstall Seat See Fig To Convert to Bagging or Discharging To SET UP Your Mower for MulchingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsCheck Engine OIL Level Before Starting the EngineTowing Carts and Other Attach MentsPurge Transmission Mowing TipsAutomatic Transmission Warm UP Mulching Mowing Tips General Recommendations Lubrication ChartEverybefore Service Dates Customer ResponsibilitiesOperator Presence System TractorBrake Operation TiresEngine Muffler Clean AIR ScreenClean AIR INTAKE/COOLING Areas CleaningTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Motion Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Replace Headlight BulbInterlocks and Relays To Adjust CarburetorTo Replace Fuse Engine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number PPR20H42STB SchematicElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive KEY Steering Assembly KEY Part NO. NO. Description Seat Assembly Wheels and Tires DecalsOptional Equipment EngineSpark Arrester 170771 Control, Throttle Mower Deck Wheel, Gauge Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PPR20H42STB specifications

The Poulan PPR20H42STB is a versatile and efficient riding mower that stands out for its performance and user-friendly features. Tailored for residential use, it is perfect for homeowners with medium to large lawns, combining power, durability, and ease of maintenance. This mower is designed to tackle a variety of terrain types, making it a reliable choice for lawn care enthusiasts.

One of the main features of the PPR20H42STB is its robust 20 horsepower Briggs & Stratton engine, which provides ample power to drive the mower efficiently across various landscapes. This engine is designed for reliability and optimal performance, ensuring that users can complete their mowing tasks with ease. The mower is equipped with a hydrostatic transmission, which facilitates smooth and precise speed adjustments without the need for manual gear changes. This feature enhances the overall driving experience, allowing operators to focus on getting the job done.

The cutting deck of the PPR20H42STB measures 42 inches, making it ideal for maneuvering around obstacles while still covering substantial ground in each pass. This size strikes a balance between efficiency and agility, allowing for effective mowing in tighter spaces such as gardens or around trees. The deck is adjustable, enabling users to select the desired cutting height between 1.5 inches and 4 inches. This versatility caters to different grass types and conditions, ensuring an even and pristine cut.

Another notable characteristic of the Poulan PPR20H42STB is its ergonomic design. The comfortable operator's seat and control layout enhance the user experience during extended mowing sessions. The steering wheel is positioned for easy access to controls, and the foot pedal allows for simple operation of the hydrostatic transmission, contributing to a more pleasant mowing experience.

Moreover, the PPR20H42STB features a spacious fuel tank that accommodates more fuel, reducing the frequency of refueling during larger mowing tasks. Its durable construction ensures longevity and reliability, making it a valuable investment for homeowners seeking an efficient lawn care solution.

In summary, the Poulan PPR20H42STB combines powerful performance, user-friendly features, and versatile mowing capabilities. It is an excellent choice for homeowners looking for a reliable riding mower to keep their lawns looking immaculate.
Top Page Image Contents