Poulan PPR20H42STB owner manual Mowing Tips, Purge Transmission, Automatic Transmission Warm UP

Page 14

OPERATION

AUTOMATIC TRANSMISSION WARM UP

Before driving the unit in cold weather, the transmission should be warmed up as follows:

Be sure the tractor is on level ground.

Place the motion control lever in neutral. Release

the parking brake and let the clutch/brake s l o w l y return to operating position.

Allow one minute for transmission to warm up. This can be done during the engine warm up period.

The attachments can be used during the engine warm- up period after the transmission has been warmed up and may require the choke control be pulled out slightly.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheel lever while the engine is run- ning.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have devel- oped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

Place tractor safely on level surface with engine off and parking brake set.

Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.

Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times.

NOTE: During this procedure there will be no movement of drive wheels. The air is being removed from hydraulic drive system.

Move motion control lever to neutral (N) position. Shut- off engine and set parking brake.

Engage transmission by placing freewheel control in driving position (See “TO TRANSPORT” in this section of manual).

Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.

Slowly move motion control lever forward, after the tractor moves approximately five (5) feet, slowly move motion control lever to reverse position. After the tractor moves approximately five (5) feet return the motion control lever to the neutral (N) position. Repeat this procedure with the motion control lever three (3) times.

Your transmission is now purged and now ready for normal operation.

MOWING TIPS

Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

The left hand side of mower should be used for trimming.

Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clippings and more uniform cutting.

When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 10).

If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

Always operate engine at full throttle when mowing to assure better mowing performance and proper dis- charge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting perfor- mance as well as the quality of cut desired.

When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

FIG. 10

14

Image 14
Contents PPR20H42STB General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat HOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Check Deck Levelness To SET UP Your Mower for MulchingCheck Tire Pressure To Convert to Bagging or DischargingOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsMents Before Starting the EngineTowing Carts and Other Attach Check Engine OIL LevelAutomatic Transmission Warm UP Mowing TipsPurge Transmission Mulching Mowing Tips Customer Responsibilities Lubrication ChartEverybefore Service Dates General RecommendationsTires TractorBrake Operation Operator Presence SystemEngine Cleaning Clean AIR ScreenClean AIR INTAKE/COOLING Areas MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Blade Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral Adjustment See Fig Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Attach Jumper CablesTo Replace Fuse To Adjust CarburetorInterlocks and Relays Fuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PPR20H42STBElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive KEY Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresSpark Arrester EngineOptional Equipment 170771 Control, Throttle Mower Deck Wheel, Gauge Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PPR20H42STB specifications

The Poulan PPR20H42STB is a versatile and efficient riding mower that stands out for its performance and user-friendly features. Tailored for residential use, it is perfect for homeowners with medium to large lawns, combining power, durability, and ease of maintenance. This mower is designed to tackle a variety of terrain types, making it a reliable choice for lawn care enthusiasts.

One of the main features of the PPR20H42STB is its robust 20 horsepower Briggs & Stratton engine, which provides ample power to drive the mower efficiently across various landscapes. This engine is designed for reliability and optimal performance, ensuring that users can complete their mowing tasks with ease. The mower is equipped with a hydrostatic transmission, which facilitates smooth and precise speed adjustments without the need for manual gear changes. This feature enhances the overall driving experience, allowing operators to focus on getting the job done.

The cutting deck of the PPR20H42STB measures 42 inches, making it ideal for maneuvering around obstacles while still covering substantial ground in each pass. This size strikes a balance between efficiency and agility, allowing for effective mowing in tighter spaces such as gardens or around trees. The deck is adjustable, enabling users to select the desired cutting height between 1.5 inches and 4 inches. This versatility caters to different grass types and conditions, ensuring an even and pristine cut.

Another notable characteristic of the Poulan PPR20H42STB is its ergonomic design. The comfortable operator's seat and control layout enhance the user experience during extended mowing sessions. The steering wheel is positioned for easy access to controls, and the foot pedal allows for simple operation of the hydrostatic transmission, contributing to a more pleasant mowing experience.

Moreover, the PPR20H42STB features a spacious fuel tank that accommodates more fuel, reducing the frequency of refueling during larger mowing tasks. Its durable construction ensures longevity and reliability, making it a valuable investment for homeowners seeking an efficient lawn care solution.

In summary, the Poulan PPR20H42STB combines powerful performance, user-friendly features, and versatile mowing capabilities. It is an excellent choice for homeowners looking for a reliable riding mower to keep their lawns looking immaculate.