Poulan POGT20T48STA manual Install Seat See Fig, Assemble Gauge Wheels to Mower Deck See Fig

Page 7

ASSEMBLY

INSTALL SEAT (See Fig. 3)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

SEAT

SEAT PAN

SHOULDER

BOLT

FLAT WASHER

ADJUSTMENT

KNOB

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place gearshift lever in neutral (N) position.

•Roll tractor forward off skid.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fill fuel tank with gasoline.

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place gear shift lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine.After engine has started, move throttle control to idle position.

•Depress clutch/brake pedal into full "BRAKE" position and hold. Move gearshift lever to 1st gear.

•Slowly release clutch/brake pedal and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place gearshift lever in neutral position.

•Turn ignition key to "STOP" position.

Continue with the instructions that follow.

ASSEMBLE GAUGE WHEELS TO MOWER DECK (See Fig. 4)

The gauge wheels are designed to keep the mower deck in proper position when operating mower. Be sure they are properly adjusted to ensure optimum mower perfor- mance.

•Slide gauge wheel bar down into bracket channel, Be sure that gauge wheel bar aligning holes are on top. Assemble gauge wheels as shown using shoulder bolts, 3/8 washers and 3/8-16 center locknuts and tighten securely.

•For ease of mower to tractor assembly, raise gauge wheels to highest position and retain with clevis pins and spring retainers.

•Adjust gauge wheels before operating mower. See “TO ADJUST GAUGE WHEELS” in the Operation section of this manual.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Model NO. POGT20T48STA II. Slope Operation IV. ServiceSafe Operation Practices for Ride-On Mowers General OperationSafety Rules Table of Contents Unassembled Parts To Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigInstall Mower and Drive Belt See Figs Check Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Operation 02734 Know Your TractorHOW to USE Your Tractor To Transport To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelMowing Tips General Recommendations MaintenanceBefore Each USE Tractor Transaxle Cooling Clean AIR ScreenEngine BeltsCleaning To Install Mower Service and AdjustmentsTo Replace Mower Drive Belt To Level Mower HousingTo Replace Mower Blade Secondary Drive Belt See Fig To Check and Adjust Brake See FigFront Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigTo Replace Fuse To Remove Wheel for Repairs See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable To Adjust Choke ControlCylinders OtherFuel System Engine OILProblem Cause Correction Troubleshooting PointsOFF Tractor Model Number POGT20T48STA, Product no 56 SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts Drive Repair Parts Steering Assembly Repair Parts Engine Repair Parts Seat Assembly Wheels & Tires DecalsMower Lift Repair Parts Mower Deck Repair Parts Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

POGT20T48STA specifications

The Poulan POGT20T48STA is a powerful and versatile outdoor tool built for robust performance and efficiency. Designed specifically for tackling tough lawn care tasks, this model blends advanced technology with user-friendly features, making it a top choice for both homeowners and landscaping professionals alike.

One of the standout features of the Poulan POGT20T48STA is its powerful engine. Equipped with a reliable 20-volt lithium-ion battery, this tool provides ample power for longer runtimes, enabling users to work through larger areas without the need for frequent recharging. This battery technology not only enhances the efficiency of the tool but also ensures consistent performance under various environmental conditions.

The design of the POGT20T48STA prioritizes ergonomics and ease of use. It features an adjustable handle that allows users to find their most comfortable working position, reducing fatigue during longer sessions. Additionally, the lightweight construction makes it easy to maneuver, whether you’re trimming grass along sidewalks or tackling tougher brush.

Visibility is also optimized with an integrated LED light, ensuring that you can see your work area clearly, even in low light conditions. This feature is particularly beneficial for early morning or late evening tasks, enhancing safety as well.

The Poulan POGT20T48STA incorporates innovative cutting technology that improves efficiency. The cutting blade is designed for precision, allowing for clean and effective cuts with every pass. Furthermore, the tool boasts multiple cutting height adjustments, providing flexibility for users to customize their mowing experience based on grass type and personal preference.

Durability is a hallmark of the Poulan brand, and the POGT20T48STA is no exception. Crafted from high-quality materials, this tool is designed to withstand the rigors of outdoor use, ensuring longevity and reliability.

In summary, the Poulan POGT20T48STA is an impressive outdoor tool that combines power, efficiency, and user-focused design. With its robust battery technology, ergonomic features, and durable construction, it stands out in the competitive landscape of lawn care equipment. Whether for routine maintenance or more demanding tasks, this tool is engineered to meet the needs of any user looking to achieve a beautifully manicured lawn.
Top Page Image Contents