Poulan POGT20T48STA manual To Remove Wheel for Repairs See Fig, To Replace Headlight Bulb

Page 24

SERVICE AND ADJUSTMENTS

TO REMOVE WHEEL FOR REPAIRS (See Fig. 26)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE

COVER

SQUARE KEY

(REAR WHEEL ONLY)

FIG. 26

TO START ENGINE WITH A WEAK BATTERY (See Fig. 27)

REPLACING BATTERY (See Fig. 28)

WARNING: Do not short battery ter- minals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

•Lift hood to raised position.

•Remove terminal guard.

•Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•Reinstall terminal guard.

•First connect RED battery cable to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely.

•Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely

•Close terminal access doors.

•Close hood.

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

TERMINAL ACCESS DOOR

TERMINAL GUARD

KEPS NUT

HEX BOLT

POSITIVE (RED)

CABLE

NEGATIVE (BLACK) CABLE

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

WEAK OR DEAD BATTERY FULLY CHARGED BATTERY

FIG. 28

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

FIG. 27

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Model NO. POGT20T48STA IV. Service Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationSafety Rules Table of Contents Unassembled Parts Assembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs Check Tire Pressure Check Mower LevelnessCheck for Proper Position of ALL Belts Operation Know Your Tractor 02734HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To TransportBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolineMowing Tips Maintenance General RecommendationsBefore Each USE Tractor Clean AIR Screen EngineBelts Transaxle CoolingCleaning Service and Adjustments To Install MowerTo Level Mower Housing To Replace Mower Drive BeltTo Check and Adjust Brake See Fig To Replace Mower Blade Secondary Drive Belt See FigTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust Steering Wheel AlignmentTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBERTo Remove Wheel for Repairs See Fig To Replace Headlight BulbInterlocks and Relays To Replace FuseTo Remove Hood and Grill Assembly See Fig To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorOther Fuel SystemEngine OIL CylindersTroubleshooting Points Problem Cause CorrectionOFF Schematic Tractor Model Number POGT20T48STA, Product no 56Electrical KEY Part Description Chassis and Enclosures Repair Parts Drive Repair Parts Steering Assembly Repair Parts Engine Repair Parts Seat Assembly Decals Wheels & TiresMower Lift Repair Parts Mower Deck Repair Parts Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

POGT20T48STA specifications

The Poulan POGT20T48STA is a powerful and versatile outdoor tool built for robust performance and efficiency. Designed specifically for tackling tough lawn care tasks, this model blends advanced technology with user-friendly features, making it a top choice for both homeowners and landscaping professionals alike.

One of the standout features of the Poulan POGT20T48STA is its powerful engine. Equipped with a reliable 20-volt lithium-ion battery, this tool provides ample power for longer runtimes, enabling users to work through larger areas without the need for frequent recharging. This battery technology not only enhances the efficiency of the tool but also ensures consistent performance under various environmental conditions.

The design of the POGT20T48STA prioritizes ergonomics and ease of use. It features an adjustable handle that allows users to find their most comfortable working position, reducing fatigue during longer sessions. Additionally, the lightweight construction makes it easy to maneuver, whether you’re trimming grass along sidewalks or tackling tougher brush.

Visibility is also optimized with an integrated LED light, ensuring that you can see your work area clearly, even in low light conditions. This feature is particularly beneficial for early morning or late evening tasks, enhancing safety as well.

The Poulan POGT20T48STA incorporates innovative cutting technology that improves efficiency. The cutting blade is designed for precision, allowing for clean and effective cuts with every pass. Furthermore, the tool boasts multiple cutting height adjustments, providing flexibility for users to customize their mowing experience based on grass type and personal preference.

Durability is a hallmark of the Poulan brand, and the POGT20T48STA is no exception. Crafted from high-quality materials, this tool is designed to withstand the rigors of outdoor use, ensuring longevity and reliability.

In summary, the Poulan POGT20T48STA is an impressive outdoor tool that combines power, efficiency, and user-focused design. With its robust battery technology, ergonomic features, and durable construction, it stands out in the competitive landscape of lawn care equipment. Whether for routine maintenance or more demanding tasks, this tool is engineered to meet the needs of any user looking to achieve a beautifully manicured lawn.
Top Page Image Contents