Poulan POGT20T48STA To Replace Motion Drive Belt See Fig, To Adjust Steering Wheel Alignment

Page 23

SERVICE AND ADJUSTMENTS

WITH PARKING BRAKE “ENGAGED”

ELECTRIC

 

CLUTCH

 

CLUTCHING

1-1/2"

IDLER

 

 

STATIONARY

 

IDLER

NUT “A”

 

 

CENTER SPAN

 

KEEPER

 

JAM NUT

 

TRANSAXLE

 

PULLEY

OPERATING ARM

CLUTCH LOCATOR

CLUTCH

WIRE

HARNESS

FIG. 24

FIG. 23

TO REPLACE MOTION DRIVE BELT (See Fig. 24)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Disconnect clutch wire harness.

•Remove clutch locator.

•Remove belt from stationary idler and clutching idler.

•Remove belt downward from engine pulley and around electric clutch.

•Pull belt slack toward rear of tractor. Remove belt upwards from transaxle pulley by deflecting belt keep- ers.

•Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

•Carefully work new belt down between transaxle belt keepers and onto the input pulley.

•Slide belt into the center span keeper.

•Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley.

•Install belt through stationary idler and clutching idler.

•Reinstall clutch locator and tighten nut securely.

•Reconnect clutch harness.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

TRANSAXLE GEAR SHIFT LEVER NEUTRAL- ADJUSTMENT (See Fig. 25)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) posi- tion.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

GEARSHIFT LEVER

NEUTRAL

ADJUSTMENT LOCK GATE

BOLT

FIG. 25

TO ADJUST STEERING WHEEL

ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized

23service center/department.

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model NO. POGT20T48STA II. Slope Operation IV. ServiceSafe Operation Practices for Ride-On Mowers General OperationSafety Rules Table of Contents Unassembled Parts To Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigInstall Mower and Drive Belt See Figs Check for Proper Position of ALL Belts Check Tire PressureCheck Mower Levelness Operation 02734 Know Your TractorHOW to USE Your Tractor To Transport To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelMowing Tips Before Each USE MaintenanceGeneral Recommendations Tractor Transaxle Cooling Clean AIR ScreenEngine BeltsCleaning To Install Mower Service and AdjustmentsTo Replace Mower Drive Belt To Level Mower HousingTo Replace Mower Blade Secondary Drive Belt See Fig To Check and Adjust Brake See FigFront Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigTo Replace Fuse To Remove Wheel for Repairs See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable To Adjust Choke ControlCylinders OtherFuel System Engine OILProblem Cause Correction Troubleshooting PointsOFF Tractor Model Number POGT20T48STA, Product no 56 SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts Drive Repair Parts Steering Assembly Repair Parts Engine Repair Parts Seat Assembly Wheels & Tires DecalsMower Lift Repair Parts Mower Deck Repair Parts Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

POGT20T48STA specifications

The Poulan POGT20T48STA is a powerful and versatile outdoor tool built for robust performance and efficiency. Designed specifically for tackling tough lawn care tasks, this model blends advanced technology with user-friendly features, making it a top choice for both homeowners and landscaping professionals alike.

One of the standout features of the Poulan POGT20T48STA is its powerful engine. Equipped with a reliable 20-volt lithium-ion battery, this tool provides ample power for longer runtimes, enabling users to work through larger areas without the need for frequent recharging. This battery technology not only enhances the efficiency of the tool but also ensures consistent performance under various environmental conditions.

The design of the POGT20T48STA prioritizes ergonomics and ease of use. It features an adjustable handle that allows users to find their most comfortable working position, reducing fatigue during longer sessions. Additionally, the lightweight construction makes it easy to maneuver, whether you’re trimming grass along sidewalks or tackling tougher brush.

Visibility is also optimized with an integrated LED light, ensuring that you can see your work area clearly, even in low light conditions. This feature is particularly beneficial for early morning or late evening tasks, enhancing safety as well.

The Poulan POGT20T48STA incorporates innovative cutting technology that improves efficiency. The cutting blade is designed for precision, allowing for clean and effective cuts with every pass. Furthermore, the tool boasts multiple cutting height adjustments, providing flexibility for users to customize their mowing experience based on grass type and personal preference.

Durability is a hallmark of the Poulan brand, and the POGT20T48STA is no exception. Crafted from high-quality materials, this tool is designed to withstand the rigors of outdoor use, ensuring longevity and reliability.

In summary, the Poulan POGT20T48STA is an impressive outdoor tool that combines power, efficiency, and user-focused design. With its robust battery technology, ergonomic features, and durable construction, it stands out in the competitive landscape of lawn care equipment. Whether for routine maintenance or more demanding tasks, this tool is engineered to meet the needs of any user looking to achieve a beautifully manicured lawn.
Top Page Image Contents