Poulan POGT20T48STA To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 13

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 8)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•Remove retainer spring and clevis pin which secure each gauge wheel bar.

•Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

•Replace retainer spring into clevis pin.

•Be sure all gauge wheels are in the same setting.

IMPORTANT:BE SURETO READJUST GAUGEWHEELS IFYOU CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.

RETAINER

SPRING

CLEVIS

PIN

FIG. 8

TO OPERATE MOWER (See Fig. 9)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

ATTACHEMNT CLUTCH SWITCH

LIFT LEVER HIGHEST

POSIITON

PULL OUT TO "ENGAGE"

 

 

LOWEST

 

POSITION

PUSH IN TO

 

"DISENGAGE"

 

 

DEFLECTOR

 

SHIELD

FIG. 9

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move gearshift lever to 1st gear. Be sure you have allowed room for tractor to roll slightly as you restart movement.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Make all turns slowly.

TO TRANSPORT

•Raise attachment lift to highest position with attachment lift control.

•When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position.

•Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Model NO. POGT20T48STA Safe Operation Practices for Ride-On Mowers IV. ServiceGeneral Operation II. Slope OperationSafety Rules Table of Contents Unassembled Parts Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigInstall Mower and Drive Belt See Figs Check Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Operation 02734 Know Your TractorHOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To TransportTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips General Recommendations MaintenanceBefore Each USE Tractor Engine Clean AIR ScreenBelts Transaxle CoolingCleaning To Install Mower Service and AdjustmentsTo Replace Mower Drive Belt To Level Mower HousingTo Replace Mower Blade Secondary Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Steering Wheel Alignment Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Remove Wheel for Repairs See FigInterlocks and Relays To Replace FuseTo Adjust Throttle Control Cable To Remove Hood and Grill Assembly See FigTo Adjust Choke Control To Adjust CarburetorFuel System OtherEngine OIL CylindersProblem Cause Correction Troubleshooting PointsOFF Tractor Model Number POGT20T48STA, Product no 56 SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts Drive Repair Parts Steering Assembly Repair Parts Engine Repair Parts Seat Assembly Wheels & Tires DecalsMower Lift Repair Parts Mower Deck Repair Parts Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

POGT20T48STA specifications

The Poulan POGT20T48STA is a powerful and versatile outdoor tool built for robust performance and efficiency. Designed specifically for tackling tough lawn care tasks, this model blends advanced technology with user-friendly features, making it a top choice for both homeowners and landscaping professionals alike.

One of the standout features of the Poulan POGT20T48STA is its powerful engine. Equipped with a reliable 20-volt lithium-ion battery, this tool provides ample power for longer runtimes, enabling users to work through larger areas without the need for frequent recharging. This battery technology not only enhances the efficiency of the tool but also ensures consistent performance under various environmental conditions.

The design of the POGT20T48STA prioritizes ergonomics and ease of use. It features an adjustable handle that allows users to find their most comfortable working position, reducing fatigue during longer sessions. Additionally, the lightweight construction makes it easy to maneuver, whether you’re trimming grass along sidewalks or tackling tougher brush.

Visibility is also optimized with an integrated LED light, ensuring that you can see your work area clearly, even in low light conditions. This feature is particularly beneficial for early morning or late evening tasks, enhancing safety as well.

The Poulan POGT20T48STA incorporates innovative cutting technology that improves efficiency. The cutting blade is designed for precision, allowing for clean and effective cuts with every pass. Furthermore, the tool boasts multiple cutting height adjustments, providing flexibility for users to customize their mowing experience based on grass type and personal preference.

Durability is a hallmark of the Poulan brand, and the POGT20T48STA is no exception. Crafted from high-quality materials, this tool is designed to withstand the rigors of outdoor use, ensuring longevity and reliability.

In summary, the Poulan POGT20T48STA is an impressive outdoor tool that combines power, efficiency, and user-focused design. With its robust battery technology, ergonomic features, and durable construction, it stands out in the competitive landscape of lawn care equipment. Whether for routine maintenance or more demanding tasks, this tool is engineered to meet the needs of any user looking to achieve a beautifully manicured lawn.
Top Page Image Contents