Poulan PK19H42LT To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 12

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 6)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a fl at level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 3/8 washer, and 3/8-16 locknut and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

GAUGE

WHEEL

MOUNTING

BRACKET

 

014

 

2

3/8-16

3

 

LOCKNUT

 

3/8 WASHER

SHOULDER

BOLT

 

 

GAUGE WHEEL

FIG. 6

TO OPERATE MOWER (See Fig. 7)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

"ENGAGED" POSITION ATTACHMENT LIFT LEVER HIGH POSITION

LOW

POSITION

DEFLECTOR

SHIELD

ATTACHMENT

CLUTCH LEVER "DISENGAGED" PO-

SITION

FIG. 7

REVERSE OPERATION SYSTEM (ROS)

Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

WARNING: Backing up with the attachment clutch en- gaged while mowing is strongly discouraged. Turning the ROS "ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator decides it is necessary to reposition the machine with the attachment engaged. Do not mow in reverse unless absolutely necessary.

USING THE REVERSE OPERATION SYSTEM -

•Move motion control lever to neutral (N) position.

•With engine running, turn ignition key counterclockwise to ROS "ON" position.

•Look down and behind before backing.

•Slowly move motion control lever to reverse (R) position to start movement.

•When use of the ROS is no longer needed, turn the ignition key clockwise to engine "ON" position.

ROS "ON" POSITION

ENGINE "ON" POSITION

 

(NORMAL OPERATING)

02828

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PK19H42LT Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Steering Wheel SeatKey Slope SheetAssembly Tools Required for AssemblyTo Remove Tractor from CAR- TON Before Removing Tractor from SkidCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig Using the Reverse Operation SystemTo Operate Mower See Fig Reverse Operation System ROSBefore Starting the Engine To Transport See FigsCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP Maintenance Maintenance ScheduleLubrication Chart General RecommendationsTractor Blade Removal See FigTo Sharpen Blade See Fig Engine Cleaning Service and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal To Check and Adjust Brake See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Brake To Replace Motion Drive Belt See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PK19H42LT specifications

The Poulan PK19H42LT is a versatile and powerful lawn tractor designed to make lawn care efficient and enjoyable. This model excels in performance, incorporating a range of features that cater to both residential and semi-professional users. Its robust 19 horsepower Briggs & Stratton engine is not only reliable but also efficient, ensuring that it can handle even the toughest mowing tasks with ease.

One of the key characteristics of the PK19H42LT is its 42-inch cutting deck, which allows for a wide cutting path to cover larger areas in shorter time frames. This deck is made of durable materials, capable of withstanding the rigors of regular use. The cutting height can be easily adjusted to five different positions, enabling users to achieve their desired grass length for a variety of conditions.

The tractor is equipped with a hydrostatic transmission, which provides a smooth and seamless driving experience. This feature gives users the ability to alter their speed without the need for manual gear shifting, enhancing overall control and maneuverability while navigating through gardens and tight spaces.

Another notable feature is the ergonomically designed steering wheel and comfortable seat, which contribute to a pleasant driving experience, even during extended periods of mowing. The design ensures that users remain comfortable, helping to reduce fatigue and allowing for more efficient lawn care sessions.

For added convenience, the PK19H42LT includes a pedal-operated deck lift system, making it easy to raise and lower the cutting deck. This makes switching between cutting heights or transitioning into storage or transportation a simple task.

Moreover, the mower's easy-to-access controls and dashboard ensure that users can operate features without difficulty. The mower is also equipped with a front bumper, providing additional protection against potential obstacles during use.

In addition to mowing, this versatile tractor can be fitted with various attachments, such as baggers, carts, and snow blades, which enhance its functionality throughout the year.

Overall, the Poulan PK19H42LT is a well-rounded lawn tractor that delivers power, versatility, and ease of use, making it an excellent choice for homeowners seeking a reliable tool for maintaining their lawns.
Top Page Image Contents