Poulan PK19H42LT manual Tractor, Blade Removal See Fig, To Sharpen Blade See Fig

Page 16

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than fi ve (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See“PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent fl at tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OP- ERATION SYSTEM (ROS)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any attempt by the operator to leave the seat without fi rst setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch en- gaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

ROS "ON" POSITION

ENGINE "ON" POSITION

 

(NORMAL OPERATING)

828

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 10)

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and flat washer securing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble blade bolt, lock washer and fl at washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS HEATTREATED.IF BOLT NEEDS REPLACING, REPLACE ONLY WITH APPROVE BOLT SHOWN IN THE REPAIR PARTS.

TRAILING EDGE UP

 

BLADE

 

 

CENTER

FLAT

HOLE

MANDREL

WASHER

ASSEMBLY

LOCK

 

WASHER

STAR

BLADE BOLT

FIG. 10

TO SHARPEN BLADE (See Fig. 11)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An un- balanced blade will cause excessive vibration and eventual damage to mower and engine.

•The blade can be sharpened with a fi le or on a grind- ing wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer).

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents PK19H42LT Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Steering Wheel SeatKey Slope SheetAssembly Tools Required for AssemblyTo Remove Tractor from CAR- TON Before Removing Tractor from SkidCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig Using the Reverse Operation SystemTo Operate Mower See Fig Reverse Operation System ROSBefore Starting the Engine To Transport See FigsCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP Maintenance Maintenance ScheduleLubrication Chart General RecommendationsBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine Cleaning Service and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal To Check and Adjust Brake See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Brake To Replace Motion Drive Belt See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PK19H42LT specifications

The Poulan PK19H42LT is a versatile and powerful lawn tractor designed to make lawn care efficient and enjoyable. This model excels in performance, incorporating a range of features that cater to both residential and semi-professional users. Its robust 19 horsepower Briggs & Stratton engine is not only reliable but also efficient, ensuring that it can handle even the toughest mowing tasks with ease.

One of the key characteristics of the PK19H42LT is its 42-inch cutting deck, which allows for a wide cutting path to cover larger areas in shorter time frames. This deck is made of durable materials, capable of withstanding the rigors of regular use. The cutting height can be easily adjusted to five different positions, enabling users to achieve their desired grass length for a variety of conditions.

The tractor is equipped with a hydrostatic transmission, which provides a smooth and seamless driving experience. This feature gives users the ability to alter their speed without the need for manual gear shifting, enhancing overall control and maneuverability while navigating through gardens and tight spaces.

Another notable feature is the ergonomically designed steering wheel and comfortable seat, which contribute to a pleasant driving experience, even during extended periods of mowing. The design ensures that users remain comfortable, helping to reduce fatigue and allowing for more efficient lawn care sessions.

For added convenience, the PK19H42LT includes a pedal-operated deck lift system, making it easy to raise and lower the cutting deck. This makes switching between cutting heights or transitioning into storage or transportation a simple task.

Moreover, the mower's easy-to-access controls and dashboard ensure that users can operate features without difficulty. The mower is also equipped with a front bumper, providing additional protection against potential obstacles during use.

In addition to mowing, this versatile tractor can be fitted with various attachments, such as baggers, carts, and snow blades, which enhance its functionality throughout the year.

Overall, the Poulan PK19H42LT is a well-rounded lawn tractor that delivers power, versatility, and ease of use, making it an excellent choice for homeowners seeking a reliable tool for maintaining their lawns.
Top Page Image Contents