Poulan PK19H42LT manual Engine

Page 17

MAINTENANCE

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

CENTER HOLE

BLADE

5/8" BOLT OR PIN

FIG. 11

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

•Disconnect BLACK battery cable fi rst then RED bat- tery cable and remove battery from tractor.

•Rinse the battery with plain water and dry.

•Clean terminals and battery cable ends with wire brush until bright.

•Coat terminals with grease or petroleum jelly.

•Reinstall battery (See “REPLACING BATTERY" in the SERVICE AND ADJUSTMENTS section of this manual).

V-BELTS

Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear.

TRANSAXLE COOLING

The transmission fan and cooling fi ns should be kept clean to assure proper cooling.

Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent pos- sible damage to seals, do not use high pressure water or steam to clean transaxle.

•Inspect cooling fan to be sure fan blades are intact and clean.

•Inspect cooling fi ns for dirt, grass clippings and other materials. To prevent damage to seals, do not use compressed air or high pressure sprayer to clean cool- ing fi ns.

TRANSAXLE PUMP FLUID

The transaxle was sealed at the factory and fl uid mainte- nance is not required for the life of the transaxle. Should the transaxle ever leak or require servicing, contact your nearest authorized service center/department.

ENGINE

LUBRICATION

Only use high quality detergent oil rated with API service classifi cation SG-SL. Select the oil’s SAE viscosity grade according to your expected operating temperature.

SAE VISCOSITY GRADES

 

 

 

 

 

 

 

 

 

 

10W30

 

 

 

 

 

 

 

5W-30

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F

-20

0

 

 

30 32 40

 

60

 

80

100

C

-30

-20

-10

0

10

20

30

40

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

oil_visc_chart4_e

FIG. 12

Change the oil after every 50 hours of operation or at least once a year if the tractor is not used for 50 hours in one year.

Check the crankcase oil level before starting the engine and after each eight (8) hours of operation.

TO CHANGE ENGINE OIL (See Figs. 12 and 13)

Determine temperature range expected before oil change. All oil must meet API service classifi cation SG-SL.

•Be sure tractor is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

•Remove oil fi ll cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil.

•Remove yellow cap from end of drain valve and install the drain tube onto the fi tting.

 

OIL DRAIN VALVE

 

 

CLOSED AND

 

 

 

LOCKED

 

 

 

POSITION

 

 

 

 

 

 

63

 

 

4

 

2

 

 

0

 

 

YELLOW

 

 

DRAIN

CAP

 

 

 

 

 

TUBE

FIG. 13

•Unlock drain valve by pushing inward and turning counterclockwise.

•To open, pull out on the drain valve.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Always Wear EYE Protection During Operation PK19H42LTSafe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Steering Wheel Seat Unassembled PartsKey Slope SheetTools Required for Assembly AssemblyTo Remove Tractor from CAR- TON Before Removing Tractor from SkidCheck Battery See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Using the Reverse Operation System To Adjust Gauge Wheels See FigTo Operate Mower See Fig Reverse Operation System ROSTo Transport See Figs Before Starting the EngineCheck Engine OIL Level ADD GasolineAutomatic Transmission Warm UP Mowing TipsPurge Transmission Maintenance Schedule MaintenanceLubrication Chart General RecommendationsTo Sharpen Blade See Fig TractorBlade Removal See Fig Engine Cleaning To Install Mower See Fig Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig Transaxle Motion Control Lever Neutral Adjustment See Fig To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigTo Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACEMENTTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PK19H42LT specifications

The Poulan PK19H42LT is a versatile and powerful lawn tractor designed to make lawn care efficient and enjoyable. This model excels in performance, incorporating a range of features that cater to both residential and semi-professional users. Its robust 19 horsepower Briggs & Stratton engine is not only reliable but also efficient, ensuring that it can handle even the toughest mowing tasks with ease.

One of the key characteristics of the PK19H42LT is its 42-inch cutting deck, which allows for a wide cutting path to cover larger areas in shorter time frames. This deck is made of durable materials, capable of withstanding the rigors of regular use. The cutting height can be easily adjusted to five different positions, enabling users to achieve their desired grass length for a variety of conditions.

The tractor is equipped with a hydrostatic transmission, which provides a smooth and seamless driving experience. This feature gives users the ability to alter their speed without the need for manual gear shifting, enhancing overall control and maneuverability while navigating through gardens and tight spaces.

Another notable feature is the ergonomically designed steering wheel and comfortable seat, which contribute to a pleasant driving experience, even during extended periods of mowing. The design ensures that users remain comfortable, helping to reduce fatigue and allowing for more efficient lawn care sessions.

For added convenience, the PK19H42LT includes a pedal-operated deck lift system, making it easy to raise and lower the cutting deck. This makes switching between cutting heights or transitioning into storage or transportation a simple task.

Moreover, the mower's easy-to-access controls and dashboard ensure that users can operate features without difficulty. The mower is also equipped with a front bumper, providing additional protection against potential obstacles during use.

In addition to mowing, this versatile tractor can be fitted with various attachments, such as baggers, carts, and snow blades, which enhance its functionality throughout the year.

Overall, the Poulan PK19H42LT is a well-rounded lawn tractor that delivers power, versatility, and ease of use, making it an excellent choice for homeowners seeking a reliable tool for maintaining their lawns.
Top Page Image Contents