Poulan PK19H42LT Tools Required for Assembly, To Remove Tractor from CAR- TON, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

3/4" wrench

Pliers

(1)

1/2" wrench

Tire pressure gauge

 

 

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CAR- TON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels fl at.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large fl at washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

5/16 HEX BOLT

5/16 LOCK WASHER

LARGE FLAT

WASHER

STEERING

WHEELSTEERING BOOT

TABS

ADAPTER

EXTENSION

SHAFT

LOWER

STEERING

SHAFT

TAB

SLOTS

FIG. 1

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and fl at washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and fl at washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PK19H42LT Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Key Unassembled PartsSteering Wheel Seat Slope SheetTo Remove Tractor from CAR- TON AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigUsing the Reverse Operation System Reverse Operation System ROSCheck Engine OIL Level Before Starting the EngineTo Transport See Figs ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP Lubrication Chart MaintenanceMaintenance Schedule General RecommendationsTractor Blade Removal See FigTo Sharpen Blade See Fig Engine Cleaning To Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal To Adjust Brake To Check and Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PK19H42LT specifications

The Poulan PK19H42LT is a versatile and powerful lawn tractor designed to make lawn care efficient and enjoyable. This model excels in performance, incorporating a range of features that cater to both residential and semi-professional users. Its robust 19 horsepower Briggs & Stratton engine is not only reliable but also efficient, ensuring that it can handle even the toughest mowing tasks with ease.

One of the key characteristics of the PK19H42LT is its 42-inch cutting deck, which allows for a wide cutting path to cover larger areas in shorter time frames. This deck is made of durable materials, capable of withstanding the rigors of regular use. The cutting height can be easily adjusted to five different positions, enabling users to achieve their desired grass length for a variety of conditions.

The tractor is equipped with a hydrostatic transmission, which provides a smooth and seamless driving experience. This feature gives users the ability to alter their speed without the need for manual gear shifting, enhancing overall control and maneuverability while navigating through gardens and tight spaces.

Another notable feature is the ergonomically designed steering wheel and comfortable seat, which contribute to a pleasant driving experience, even during extended periods of mowing. The design ensures that users remain comfortable, helping to reduce fatigue and allowing for more efficient lawn care sessions.

For added convenience, the PK19H42LT includes a pedal-operated deck lift system, making it easy to raise and lower the cutting deck. This makes switching between cutting heights or transitioning into storage or transportation a simple task.

Moreover, the mower's easy-to-access controls and dashboard ensure that users can operate features without difficulty. The mower is also equipped with a front bumper, providing additional protection against potential obstacles during use.

In addition to mowing, this versatile tractor can be fitted with various attachments, such as baggers, carts, and snow blades, which enhance its functionality throughout the year.

Overall, the Poulan PK19H42LT is a well-rounded lawn tractor that delivers power, versatility, and ease of use, making it an excellent choice for homeowners seeking a reliable tool for maintaining their lawns.
Top Page Image Contents