Poulan PDGT26H48B To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 13

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•Remove retainer spring and clevis pin which secure each gauge wheel bar.

•Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

•Replace retainer spring into clevis pin.

•Be sure all gauge wheels are in the same setting.

IMPORTANT:BE SURETO READJUST GAUGEWHEELS IFYOU CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.

RETAINER

SPRING

CLEVIS

PIN

FIG. 9

TO OPERATE MOWER (See Fig. 10)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Lower mower with attachment lift control.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

LIFT LEVER

HIGHEST

POSIITON

LOWEST

POSITION

ATTACHEMNT

CLUTCH

SWITCH PULL

OUT TO

"ENGAGE"

PUSH IN TO

"DISENGAGE"

DEFLECTOR

SHIELD

FIG. 10

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If stopping is absolutely necessary, push brake pedal quickly to brake position and engage parking brake.

IMPORTANT: THE MOTION CONTROL LEVER RETURNS TO NEUTRAL (N) POSITION WHEN THE BRAKE PEDAL IS FULLY DEPRESSED.

•To restart movement, slowly release parking brake and brake pedal.

•Slowly move motion control lever to slowest setting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 7 and 11)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attachment lift control.

•Pull freewheel control out and into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents PDGT26H48B Safe Operation Practices for RIDE-ON Mowers IV. ServiceGeneral Operation II. Slope OperationTable of Contents Customer Responsibilities Product SpecificationsUnassembled Parts Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See FigsCheck Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Operation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP General Recommendations MaintenanceBefore Each USE Tractor Belts EngineTransaxle Cooling Transaxle Pump FluidCleaning To Install Mower Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Drive Belt To Replace Mower Blade Secondary Drive Belt See Fig To Adjust Attachment Clutch See FigTransmission REMOVAL/REPLACEMENT To Check and Adjust BrakeTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERReplacing Battery See Fig To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs To Replace Headlight Bulb To Remove Hood and Grill Assembly See FigInterlocks and Relays To Replace FuseTo Adjust Choke Control See Fig To Adjust Throttle Control Cable See FigTo Adjust Carburetor Fuel System OtherEngine OIL CylindersProblem Cause Correction Troubleshooting PointsOFF Tractor Model Number PDGT26H48B, Product Number 954 56 SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts 153 Ground DriveTransaxle Hydro Gear Steering Assembly 180656 Wheel, Steering Spark Arrester KIT EngineLift Assembly Seat Assembly Wheels & Tires DecalsMower Deck KEY Part NO. NO. Description Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PDGT26H48B specifications

The Poulan PDGT26H48B is a robust and reliable garden tractor designed to provide users with a powerful and efficient mowing experience. With its 26 HP Briggs & Stratton engine, this machine is built to tackle even the toughest grass and terrain with ease. The engine is engineered for long-lasting performance, delivering ample power to handle various mowing conditions effectively.

One of the standout features of the PDGT26H48B is its 48-inch cutting deck. This wide cutting path allows for efficient mowing, reducing the time spent on larger lawns. Additionally, the deck is adjustable, providing users with six different cutting heights, ensuring that they can achieve the desired finish for their lawns, whether it's a tidy trim or a longer cut for a more natural look.

The Poulan PDGT26H48B is equipped with a hydrostatic transmission, which offers a smooth and seamless driving experience. This technology allows for easy acceleration and deceleration without the need for gear shifting, making it user-friendly, especially for those who may not be accustomed to operating heavier machinery. The control is intuitive, enabling its operators to focus on the mowing task rather than on complicated driving maneuvers.

Comfort is also a key characteristic of this model. The ergonomic design includes a comfortable high-back seat that provides support during long mowing sessions. The easily accessible controls and dashboard keep critical information within view, making it easy for users to monitor their working conditions.

In terms of durability, the Poulan PDGT26H48B features a rugged construction that can withstand the rigors of regular use in various conditions. The steel frame and reinforced deck contribute to its longevity, ensuring that users get a solid return on their investment.

Additionally, the PDGT26H48B boasts a number of convenience features, such as a cup holder and storage compartment, allowing users to keep essential items close during their mowing tasks. The easy-to-access oil drain and maintenance points further enhance the serviceability of the tractor, making routine upkeep a breeze.

In summary, the Poulan PDGT26H48B combines power, comfort, and user-friendly features, making it a compelling choice for homeowners seeking an efficient and dependable garden tractor. Whether handling small lawns or larger landscapes, this machine is equipped to meet a variety of mowing needs with ease and precision.
Top Page Image Contents