Poulan PDGT26H48B owner manual To Level Mower Housing, FRONT-TO-BACK Adjustment See Figs

Page 21

SERVICE AND ADJUSTMENTS

NOTE: To assist in locating hole in flanged pin, the hole in pin is inline with notch on head of pin. If necessary, move mower side-to-side to give space between plate and mower brackets.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

•Engage belt tension rod by pushing rod into locking bracket.

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.

•Connect anti-sway bar to chassis bracket under left footrest and retain with double loop retainer spring.

•If equipped, turn height adjustment knob clockwise to remove slack from mower suspension.

•Raise deck to highest position.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 20 and 21)

•Raise mower to its highest position.

•Measure height from bottom edge of mower to ground level at front corners of mower. Distance “A” on both sides of mower should be the same.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Recheck measurements after adjusting.

BOTTOM EDGE

BOTTOM EDGE

OF MOWER TO

OF MOWER TO

GROUND

GROUND

A

GROUND LINE

A

FIG. 20

SUSPENSION

ARM

LIFT LINK

ADJUSTMENT NUT

FIG. 21

FRONT-TO-BACK ADJUSTMENT (See Figs. 22 and 23)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is approximately 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

Check adjustment on right side of tractor. Position any blade so the tip is pointing straight forward. Measure distance "B" at front and rear tip of the blade.

•Before making any necessary adjustments, check that both front plate links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of blade, loosen nut “C” on both front links an equal number of turns.

NOTE: Each full turn of nut “C” will change distance. “B” by approximately 3/16".

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•To raise front of blade, loosen nut “D” from trunnion on both front links. Tighten nut “C” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•Recheck side-to-side adjustment.

BLADE

“B”“B”

FIG. 22

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents PDGT26H48B Safe Operation Practices for RIDE-ON Mowers IV. ServiceGeneral Operation II. Slope OperationTable of Contents Customer Responsibilities Product SpecificationsUnassembled Parts Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See FigsCheck Tire Pressure Check Mower LevelnessCheck for Proper Position of ALL Belts Operation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP Maintenance General RecommendationsBefore Each USE Tractor Belts EngineTransaxle Cooling Transaxle Pump FluidCleaning Service and Adjustments To Install MowerTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Drive Belt To Replace Mower Blade Secondary Drive Belt See Fig To Adjust Attachment Clutch See FigTransmission REMOVAL/REPLACEMENT To Check and Adjust BrakeTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Remove Wheel for Repairs To Replace Headlight Bulb To Remove Hood and Grill Assembly See FigInterlocks and Relays To Replace FuseTo Adjust Throttle Control Cable See Fig To Adjust Choke Control See FigTo Adjust Carburetor Fuel System OtherEngine OIL CylindersProblem Cause Correction Troubleshooting PointsOFF Tractor Model Number PDGT26H48B, Product Number 954 56 SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts 153 Ground DriveTransaxle Hydro Gear Steering Assembly 180656 Wheel, Steering Spark Arrester KIT EngineLift Assembly Seat Assembly Wheels & Tires DecalsMower Deck KEY Part NO. NO. Description Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PDGT26H48B specifications

The Poulan PDGT26H48B is a robust and reliable garden tractor designed to provide users with a powerful and efficient mowing experience. With its 26 HP Briggs & Stratton engine, this machine is built to tackle even the toughest grass and terrain with ease. The engine is engineered for long-lasting performance, delivering ample power to handle various mowing conditions effectively.

One of the standout features of the PDGT26H48B is its 48-inch cutting deck. This wide cutting path allows for efficient mowing, reducing the time spent on larger lawns. Additionally, the deck is adjustable, providing users with six different cutting heights, ensuring that they can achieve the desired finish for their lawns, whether it's a tidy trim or a longer cut for a more natural look.

The Poulan PDGT26H48B is equipped with a hydrostatic transmission, which offers a smooth and seamless driving experience. This technology allows for easy acceleration and deceleration without the need for gear shifting, making it user-friendly, especially for those who may not be accustomed to operating heavier machinery. The control is intuitive, enabling its operators to focus on the mowing task rather than on complicated driving maneuvers.

Comfort is also a key characteristic of this model. The ergonomic design includes a comfortable high-back seat that provides support during long mowing sessions. The easily accessible controls and dashboard keep critical information within view, making it easy for users to monitor their working conditions.

In terms of durability, the Poulan PDGT26H48B features a rugged construction that can withstand the rigors of regular use in various conditions. The steel frame and reinforced deck contribute to its longevity, ensuring that users get a solid return on their investment.

Additionally, the PDGT26H48B boasts a number of convenience features, such as a cup holder and storage compartment, allowing users to keep essential items close during their mowing tasks. The easy-to-access oil drain and maintenance points further enhance the serviceability of the tractor, making routine upkeep a breeze.

In summary, the Poulan PDGT26H48B combines power, comfort, and user-friendly features, making it a compelling choice for homeowners seeking an efficient and dependable garden tractor. Whether handling small lawns or larger landscapes, this machine is equipped to meet a variety of mowing needs with ease and precision.
Top Page Image Contents