Poulan PDGT26H48B To Remove Wheel for Repairs, To Start Engine with a Weak Battery See Fig

Page 25

SERVICE AND ADJUSTMENTS

TO REMOVE WHEEL FOR REPAIRS

FRONT WHEEL (See Fig. 29)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal.

•Repair tire and reassemble.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

REAR WHEEL -

•Block rear axle securely.

•Remove five (5) hub bolts to allow wheel removal.

•Repair tire and reassemble. Replace and tighten hub bolts securely.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

AXLE

COVER

00663

FIG. 29

TO START ENGINE WITH A WEAK BATTERY (See Fig. 30)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

FIG. 30

REPLACING BATTERY (See Fig. 31)

WARNING: Do not short battery ter- minals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

•Lift hood to raised position.

•Remove terminal guard.

•Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•Reinstall terminal guard.

•First connect RED battery cable to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely.

•Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely

•Close terminal access doors.

•Close hood.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents PDGT26H48B Safe Operation Practices for RIDE-ON Mowers IV. ServiceGeneral Operation II. Slope OperationTable of Contents Customer Responsibilities Product SpecificationsUnassembled Parts Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See FigsCheck Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Operation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP General Recommendations MaintenanceBefore Each USE Tractor Belts EngineTransaxle Cooling Transaxle Pump FluidCleaning To Install Mower Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Drive Belt To Replace Mower Blade Secondary Drive Belt See Fig To Adjust Attachment Clutch See FigTransmission REMOVAL/REPLACEMENT To Check and Adjust BrakeTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERReplacing Battery See Fig To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs To Replace Headlight Bulb To Remove Hood and Grill Assembly See FigInterlocks and Relays To Replace FuseTo Adjust Choke Control See Fig To Adjust Throttle Control Cable See FigTo Adjust Carburetor Fuel System OtherEngine OIL CylindersProblem Cause Correction Troubleshooting PointsOFF Tractor Model Number PDGT26H48B, Product Number 954 56 SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts 153 Ground DriveTransaxle Hydro Gear Steering Assembly 180656 Wheel, Steering Spark Arrester KIT EngineLift Assembly Seat Assembly Wheels & Tires DecalsMower Deck KEY Part NO. NO. Description Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PDGT26H48B specifications

The Poulan PDGT26H48B is a robust and reliable garden tractor designed to provide users with a powerful and efficient mowing experience. With its 26 HP Briggs & Stratton engine, this machine is built to tackle even the toughest grass and terrain with ease. The engine is engineered for long-lasting performance, delivering ample power to handle various mowing conditions effectively.

One of the standout features of the PDGT26H48B is its 48-inch cutting deck. This wide cutting path allows for efficient mowing, reducing the time spent on larger lawns. Additionally, the deck is adjustable, providing users with six different cutting heights, ensuring that they can achieve the desired finish for their lawns, whether it's a tidy trim or a longer cut for a more natural look.

The Poulan PDGT26H48B is equipped with a hydrostatic transmission, which offers a smooth and seamless driving experience. This technology allows for easy acceleration and deceleration without the need for gear shifting, making it user-friendly, especially for those who may not be accustomed to operating heavier machinery. The control is intuitive, enabling its operators to focus on the mowing task rather than on complicated driving maneuvers.

Comfort is also a key characteristic of this model. The ergonomic design includes a comfortable high-back seat that provides support during long mowing sessions. The easily accessible controls and dashboard keep critical information within view, making it easy for users to monitor their working conditions.

In terms of durability, the Poulan PDGT26H48B features a rugged construction that can withstand the rigors of regular use in various conditions. The steel frame and reinforced deck contribute to its longevity, ensuring that users get a solid return on their investment.

Additionally, the PDGT26H48B boasts a number of convenience features, such as a cup holder and storage compartment, allowing users to keep essential items close during their mowing tasks. The easy-to-access oil drain and maintenance points further enhance the serviceability of the tractor, making routine upkeep a breeze.

In summary, the Poulan PDGT26H48B combines power, comfort, and user-friendly features, making it a compelling choice for homeowners seeking an efficient and dependable garden tractor. Whether handling small lawns or larger landscapes, this machine is equipped to meet a variety of mowing needs with ease and precision.
Top Page Image Contents