Poulan PDGT26H48B owner manual Install Seat See Fig, Assemble Gauge Wheels to Mower Deck See Fig

Page 7

ASSEMBLY

INSTALL SEAT (See Fig. 3)

Adjust seat before tightening adjustment knob.

Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

Lower seat into operating position and sit on seat.

Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

Get off seat without moving its adjusted position.

Raise seat and tighten adjustment knob securely.

SEAT

SEAT PAN

SHOULDER

BOLT

02466

FLAT WASHER

ADJUSTMENT

02464

KNOB

 

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

Press lift lever plunger and raise attachment lift lever to its highest position.

Release parking brake by depressing brake pedal.

Place freewheel control in disengaged position to dis- engage transmission (See “TO TRANSPORT” in the Operation section of this manual).

Roll tractor forward off skid.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

Be sure all the above assembly steps have been com- pleted.

Check engine oil level and fill fuel tank with gasoline.

Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

Sit on seat in operating position, depress brake pedal and set the parking brake.

Press lift lever plunger and raise attachment lift lever to its highest position.

Start the engine.After engine has started, move throttle control to idle position.

Release parking brake.

Slowly move the motion control lever forward and slowly drive tractor off skid.

Apply brake to stop tractor and set parking brake.

Turn ignition key to "STOP" position.

Continue with the instructions that follow.

ASSEMBLE GAUGE WHEELS TO MOWER DECK (See Fig. 4)

The gauge wheels are designed to keep the mower deck in proper position when operating mower. Be sure they are properly adjusted to ensure optimum mower perfor-

mance.

Slide gauge wheel bar down into bracket channel, Be sure that gauge wheel bar aligning holes are on top. Assemble gauge wheels as shown using shoulder bolts, 3/8 washers and 3/8-16 center locknuts and tighten securely.

For ease of mower to tractor assembly, raise gauge wheels to highest position and retain with clevis pins and spring retainers.

Adjust gauge wheels before operating mower. See “TO ADJUST GAUGE WHEELS” in the Operation section of this manual.

RETAINER

SPRING

PIN

SHOULDER

BOLT

ADJUSTING

BAR

GAUGE

 

WHEEL

3/8-16 CENTER

3/8 WASHER

 

LOCKNUT

FIG. 4

7

Image 7
Contents PDGT26H48B II. Slope Operation IV. ServiceSafe Operation Practices for RIDE-ON Mowers General OperationTable of Contents Customer Responsibilities Product SpecificationsUnassembled Parts To Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See FigsCheck Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Operation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelPurge Transmission Mowing TipsAutomatic Transmission Warm UP General Recommendations MaintenanceBefore Each USE Tractor Transaxle Pump Fluid EngineBelts Transaxle CoolingCleaning To Install Mower Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Drive Belt To Replace Mower Blade Secondary Drive Belt See Fig To Adjust Attachment Clutch See FigFront Wheel TOE-IN/CAMBER To Check and Adjust BrakeTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentReplacing Battery See Fig To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs To Replace Fuse To Remove Hood and Grill Assembly See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Choke Control See Fig To Adjust Throttle Control Cable See FigTo Adjust Carburetor Cylinders OtherFuel System Engine OILProblem Cause Correction Troubleshooting PointsOFF Tractor Model Number PDGT26H48B, Product Number 954 56 SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts 153 Ground DriveTransaxle Hydro Gear Steering Assembly 180656 Wheel, Steering Spark Arrester KIT EngineLift Assembly Seat Assembly Wheels & Tires DecalsMower Deck KEY Part NO. NO. Description Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PDGT26H48B specifications

The Poulan PDGT26H48B is a robust and reliable garden tractor designed to provide users with a powerful and efficient mowing experience. With its 26 HP Briggs & Stratton engine, this machine is built to tackle even the toughest grass and terrain with ease. The engine is engineered for long-lasting performance, delivering ample power to handle various mowing conditions effectively.

One of the standout features of the PDGT26H48B is its 48-inch cutting deck. This wide cutting path allows for efficient mowing, reducing the time spent on larger lawns. Additionally, the deck is adjustable, providing users with six different cutting heights, ensuring that they can achieve the desired finish for their lawns, whether it's a tidy trim or a longer cut for a more natural look.

The Poulan PDGT26H48B is equipped with a hydrostatic transmission, which offers a smooth and seamless driving experience. This technology allows for easy acceleration and deceleration without the need for gear shifting, making it user-friendly, especially for those who may not be accustomed to operating heavier machinery. The control is intuitive, enabling its operators to focus on the mowing task rather than on complicated driving maneuvers.

Comfort is also a key characteristic of this model. The ergonomic design includes a comfortable high-back seat that provides support during long mowing sessions. The easily accessible controls and dashboard keep critical information within view, making it easy for users to monitor their working conditions.

In terms of durability, the Poulan PDGT26H48B features a rugged construction that can withstand the rigors of regular use in various conditions. The steel frame and reinforced deck contribute to its longevity, ensuring that users get a solid return on their investment.

Additionally, the PDGT26H48B boasts a number of convenience features, such as a cup holder and storage compartment, allowing users to keep essential items close during their mowing tasks. The easy-to-access oil drain and maintenance points further enhance the serviceability of the tractor, making routine upkeep a breeze.

In summary, the Poulan PDGT26H48B combines power, comfort, and user-friendly features, making it a compelling choice for homeowners seeking an efficient and dependable garden tractor. Whether handling small lawns or larger landscapes, this machine is equipped to meet a variety of mowing needs with ease and precision.