Poulan PDGT26H48C To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 13

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•Remove retainer spring and clevis pin which secure each gauge wheel bar.

•Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

•Replace retainer spring into clevis pin.

•Be sure all gauge wheels are in the same setting.

IMPORTANT:BE SURETO READJUST GAUGEWHEELS IFYOU CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.

RETAINER

SPRING

019

77

 

CLEVIS

PIN

FIG. 9

TO OPERATE MOWER (See Fig. 10)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut.

•Lower mower with attachment lift control.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

 

 

LIFT LEVER

 

 

HIGHEST

 

 

POSIITON

 

 

LOWEST

 

 

POSITION

ATTACHEMNT

 

 

CLUTCH

 

 

SWITCH PULL

 

 

OUT TO

 

 

"ENGAGE"

 

 

PUSH IN TO

 

 

"DISENGAGE"

02142

DEFLECTOR

 

 

 

 

 

SHIELD

FIG. 10

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If stopping is absolutely necessary, push brake pedal quickly to brake position and engage parking brake.

IMPORTANT: THE MOTION CONTROL LEVER RETURNS TO NEUTRAL (N) POSITION WHEN THE BRAKE PEDAL IS FULLY DEPRESSED.

•To restart movement, slowly release parking brake and brake pedal.

•Slowly move motion control lever to slowest setting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 7 and 11)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attachment lift control.

•Pull freewheel control out and into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents PDGT26H48C Safe Operation Practices for RIDE-ON Mowers IV. ServiceGeneral Operation II. Slope OperationTable of Contents Customer Responsibilities Product SpecificationsUnassembled Parts Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See FigsCheck Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Operation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP General Recommendations MaintenanceBefore Each USE Tractor Belts EngineTransaxle Cooling Transaxle Pump FluidCleaning To Install Mower Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Secondary Drive Belt See Fig To Replace Mower Drive BeltTo Check and Adjust Brake To Adjust Attachment Clutch See FigTransaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Start Engine with a Weak Battery See Fig To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight Bulb Interlocks and RelaysFuel System OtherEngine OIL CylindersProblem Cause Correction Troubleshooting PointsWith attachment clutch Tractor Model Number PDGT26H48C SchematicElectrical KEY Part Description Chassis and Enclosures 183569 Bracket Asm., Fender 153 Ground DriveTransaxle Hydro Gear Steering Assembly 180656 Wheel, Steering Engine KEY Part NO. NO. Description Lift Assembly Repair Parts Seat Assembly Wheels & Tires DecalsMower Deck KEY Part NO. NO. Description Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PDGT26H48C specifications

The Poulan PDGT26H48C is a versatile and robust lawn tractor designed for homeowners seeking efficiency and performance in lawn maintenance. With its powerful engine and durable construction, it stands out in the lawn care market, making it a reliable choice for mowing larger yards.

At the heart of the PDGT26H48C is a 26-horsepower Briggs & Stratton engine, known for its reliability and fuel efficiency. This engine provides ample power for tackling tough mowing tasks, and the automatic transmission ensures smooth acceleration and easy handling. The responsive controls contribute to an enjoyable mowing experience, allowing users to maneuver around obstacles with ease.

One of the key features of the Poulan PDGT26H48C is its 48-inch cutting deck, which allows for wide cutting swath and faster mowing. The deck is designed with three adjustable blades, providing a clean and even cut regardless of the grass type or terrain. With cutting height adjustments ranging from 1 to 4 inches, users can customize their mowing height for optimal results throughout the growing season.

The lawn tractor incorporates a versatile bagging and mulching system. The included rear bagger collects clippings for easy disposal, while the mulching option finely chops the grass to return nutrients to the soil, promoting a healthy lawn ecosystem. This adaptability makes the PDGT26H48C suitable for various mowing preferences.

Additionally, the tractor is equipped with large, rugged wheels that provide excellent traction and stability on uneven terrain. The comfortable high-back seat ensures ease of use during longer mowing sessions, while the ergonomic design allows for reduced operator fatigue.

Another notable characteristic is the convenient front-mounted headlights, which extend usability into the early morning or late evening hours. This feature is particularly beneficial during busy seasons when time is of the essence.

Overall, the Poulan PDGT26H48C represents a blend of power, comfort, and innovative features, making it a valuable tool for homeowners looking to maintain their lawns efficiently. Whether tackling large lawns or navigating tricky landscaping, this lawn tractor promises reliability and ease of use.
Top Page Image Contents