Poulan PDGT26H48C owner manual Service and Adjustments, To Remove Mower See Fig, To Install Mower

Page 20

SERVICE AND ADJUSTMENTS

WARNING:TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

•Depress brake pedal fully and set parking brake.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 19)

•Place attachment clutch in “DISENGAGED” position.

•If equipped, turn height adjustment knob to lowest setting.

•Lower mower to its lowest position.

•Disengage belt tension rod from lock bracket.

CAUTION: Rod is spring loaded. Have a tight grip on rod and release slowly.

•Remove retainer spring holding anti-swaybar to chassis bracket and disengage anti-swaybar from bracket.

•Remove four retainer springs from front plate assembly and remove plate.

•Remove retainer springs from suspension arms at deck and disengage arms from deck.

•Raise attachment lift to its highest position.

Slide mower forward and remove belt from electric clutch pulley.

•Slide mower out from under right side of tractor.

TO INSTALL MOWER

Be sure tractor is on level surface and mower suspension arms are raised with attachment lift control. Engage park- ing brake.

•Swing anti-sway bar to left side of mower deck.

•Slide mower under tractor with deflector shield to right

side of tractor.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

•If equipped, turn height adjustment knob counter- clockwise until it stops.

•Lower mower linkage with attachment lift control.

•Be sure belt tension rod is in disengaged position.

•Install belt into electric clutch pulley groove.

•Place the suspension arms on outward pointing deck pins. Retain with double loop retainer spring with loops up as shown.

•Install front plate assembly to tractor suspension brackets and retain with single loop retainer springs as shown.

•Position front plate assembly between front mower brackets. Raise deck and plate assembly to align holes and insert flanged pins. Secure pins with double loop retainer springs between the plate assembly and mower brackets.

NOTE: To assist in locating hole in flanged pin, the hole in pin is inline with notch on head of pin. If necessary, move mower side-to-side to give space between plate and mower brackets.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

BELT TENSION ROD (DISENGAGED POSITION)

CHASSIS

BRACKET

RETAINER SPRING

USE PLIERS FOR

RETAINER SPRINGS

LOOP UP

LOCK BRACKET

 

 

SUSPENSION

ELECTRIC

FRONT

ARMS

CLUTCH

FRONT

PULLEY

PLATE

MOWER

 

ASSEMBLY

BRACKET

 

DOUBLE LOOP

 

RETAINER

 

SPRING

 

SINGLE LOOP

 

RETAINER

 

SPRING

 

FLANGED PIN

ANTI-SWAY

 

BAR

 

SUSPENSION ARMS DOUBLE

DEFLECTOR

SHIELD

LOOP RETAINER SPRINGS

 

(Outward pointing deck pins)

 

 

02565

FIG. 19

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents PDGT26H48C IV. Service Safe Operation Practices for RIDE-ON MowersGeneral Operation II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesUnassembled Parts Assembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs To Attach Nose Roller See FigCheck for Proper Position of ALL Belts Check Tire PressureCheck Mower Levelness Operation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolineAutomatic Transmission Warm UP Mowing TipsPurge Transmission Before Each USE MaintenanceGeneral Recommendations Tractor Engine BeltsTransaxle Cooling Transaxle Pump FluidCleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Drive Belt To Replace Mower Blade Secondary Drive Belt See FigTo Adjust Attachment Clutch See Fig To Check and Adjust BrakeTransaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight Bulb Interlocks and RelaysOther Fuel SystemEngine OIL CylindersTroubleshooting Points Problem Cause CorrectionWith attachment clutch Schematic Tractor Model Number PDGT26H48CElectrical KEY Part Description Chassis and Enclosures 183569 Bracket Asm., Fender Ground Drive 153Transaxle Hydro Gear Steering Assembly 180656 Wheel, Steering Engine KEY Part NO. NO. Description Lift Assembly Repair Parts Seat Assembly Decals Wheels & TiresMower Deck KEY Part NO. NO. Description Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PDGT26H48C specifications

The Poulan PDGT26H48C is a versatile and robust lawn tractor designed for homeowners seeking efficiency and performance in lawn maintenance. With its powerful engine and durable construction, it stands out in the lawn care market, making it a reliable choice for mowing larger yards.

At the heart of the PDGT26H48C is a 26-horsepower Briggs & Stratton engine, known for its reliability and fuel efficiency. This engine provides ample power for tackling tough mowing tasks, and the automatic transmission ensures smooth acceleration and easy handling. The responsive controls contribute to an enjoyable mowing experience, allowing users to maneuver around obstacles with ease.

One of the key features of the Poulan PDGT26H48C is its 48-inch cutting deck, which allows for wide cutting swath and faster mowing. The deck is designed with three adjustable blades, providing a clean and even cut regardless of the grass type or terrain. With cutting height adjustments ranging from 1 to 4 inches, users can customize their mowing height for optimal results throughout the growing season.

The lawn tractor incorporates a versatile bagging and mulching system. The included rear bagger collects clippings for easy disposal, while the mulching option finely chops the grass to return nutrients to the soil, promoting a healthy lawn ecosystem. This adaptability makes the PDGT26H48C suitable for various mowing preferences.

Additionally, the tractor is equipped with large, rugged wheels that provide excellent traction and stability on uneven terrain. The comfortable high-back seat ensures ease of use during longer mowing sessions, while the ergonomic design allows for reduced operator fatigue.

Another notable characteristic is the convenient front-mounted headlights, which extend usability into the early morning or late evening hours. This feature is particularly beneficial during busy seasons when time is of the essence.

Overall, the Poulan PDGT26H48C represents a blend of power, comfort, and innovative features, making it a valuable tool for homeowners looking to maintain their lawns efficiently. Whether tackling large lawns or navigating tricky landscaping, this lawn tractor promises reliability and ease of use.
Top Page Image Contents